3. An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 10.5 MPa in the vertical direction (see figure part b). Also, shear stresses of magnitude 12.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40° from the horizontal. Show these stresses on a sketch of an element oriented at this angle. (__/10)

3. An element in plane stress on the fuselage of an airplane (figure part a) is subjected to compressive stresses of magnitude 35 MPa in the horizontal direction and tensile stresses of magnitude 10.5 MPa in the vertical direction (see figure part b). Also, shear stresses of magnitude 12.5 MPa act in the directions shown. Determine the stresses acting on an element oriented at a clockwise angle of 40° from the horizontal. Show these stresses on a sketch of an element oriented at this angle. (__/10)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stresses shown in the figure act at a point in a stressedbody. Determine the normal and shear stresses at this point on theinclined plane shown
A thin-walled cylindrical pressure vessel of inner radius r = 0.6 cm and a thickness of 0.06 cm is subjected simultaneously to internal gas pressure p = 3.5 MPa, a compressive force F = 800 N acting at the ends, and a torsional load of 25 N · m (see figure). Determine the following quantities (a) the principal stresses at a point H on the surface of the vessel and the absolute maximum shear stress; (b) the normal strain along x-axis (ɛx) and the shear strain (yxy) at the same point H. See the established Oxy coordinate system. The Young's modulus of the material is 200 GPa and the Poisson's ratio is 0.3. Hint: the cross-section of the vessel can be regarded as a hollow tube and the cross-section area can be calculated as 1(0.00662 – 0.006²). You can do the same treatment for the polar moment inertia. 25 N· m F F H X 25 N· m
1) The state of stress on an element is shown in following figure. i) Determine the stresses acting on an element oriented at a counterclockwise angle of 48° from the horizontal. Show these stresses on a properly oriented element. ii) Determine the principal stresses and the principal angle. Show these stresses on a properly oriented element. iii) Determine the maximum shear stress, angle for maximum shear stress and normal stresses when maximum shear stress exists. Show these stresses on a properly oriented element. 140 MPa A 42 MPa 60 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S=600 psi, Sy = 2900 psi, and S 790 psi. (a) Draw Mohr's circle for this state of stress. (b) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (c) Show these stresses on an appropriate sketch (e.g, see Fig. 12.15 or Fig. 12.16) (d) Determine the absolute maximum shear stress at the point. Sy Part 1 Calculate the average normal stress and determine the radius of Mohr's Circle. Then draw Mohr's Circle for this state of stress. Answer: psi R = psi
The state of plane stress at a point on the surface of the airplane fuselage is represented by the stress element shown in the figure. Using Mohr's Circle, determine a) the principal stresses and the maximum in-plane shear stress specifying the orientation of the element in each case. b) The equivalent state of stress at the point on the element that is oriented {a} clockwise from this position Draw all the corresponding stress elements. Given x = {x} MPa; y = {y} MPa and xy = {xy} MPa xy MPa y y MPa 10000 x MPa →→→→x Solve in terms of variables
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
PROBLEM 3. The stress condition at one point in the tail region of the National Combat Aircraft is shown in the figure. (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point. 40 MPa TAI 200 MPa 80 MPa
Grandpa/Shutterstock.com 7.3-26 An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of σ = -45 MPa and 7xy = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress o,. (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element. PROBLEM 7.3-26 T P o, Т 139 MPa 45 MPa
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 120 MPa, Sy = 163 MPa, and Sxy = 65 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sy Sxy Sx
Q-1 Figure Q-1, below, shows Mohr’s circle for a point in a physical object that is subjected to plane stress. Determine the stresses σx, σy, and τxy, and show them on a stress element, properly oriented with reference to x-y axes. Determine the principal stresses σ1, σ2, and τmax and show them on a stress element properly rotated with respect to the x–y element Determine the stresses σn, σt, and τnt, and show them on a stress element that is properly rotated with respect to the x–y The sketches must include the magnitude of the angles w.r.t. positive x-axis as well as the angle between the x and n axes, and an indication of the direction of rotations (i.e., either clockwise (c.w.) or counterclockwise (c.c.w.)).
The state of stress at a point in a structure is shown in the following figure.(a) find the main stresses (Show the results on a sketch ofcorrectly oriented).(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).