Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 120 MPa, Sy = 163 MPa, and Sxy = 65 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 120 MPa, Sy = 163 MPa, and Sxy = 65 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 6 mm thick plate is to be punched of a shape shown in figure. Determine the minimum punching force to be applied on punch. The ultimate shear strength of the plate is 320 MPa. What is the corresponding compressive stress in the punch?
Thank you for answering this question. Please you specify each step as soon as possible. Good Luck! Thank You. For a 60° angle lamina that subjected loads shown below, 15 MPa T 3.5 MPa 1.4 MPa Ox = -3.5 MPa, oy = 15 MPa, Txy = -1.4 MPa Calculate the stresses in L-T directions (ơ1, ơr, TLt) Determine whether the lamina will fail under these applied loads by using Tsai-Hill failure criteria. Determine whether the lamina will fail under these applied loads by using maximum stress failure criteria. Mechanical properties: EL = 14 GPa; ET=3.5 GPA; GLT = 4.2 GPa; vt = 0.40 Strength (In case of tension): OLU = 250 MPa, ơTu = 10 MPa Strength (In case of compression): OLU = 200 MPa, ơTu = 0.5 MPa Shear strength: TLTU = 8 MPa OT + OLu + <1 Tsai-Hill criterion: OLu - OLu
Part (1): A 30 ?? square plate is subjected to uniform pressure as shown in Figure.1. The 2D loading stresses are described. If the modulus of elasticity is 200 ??? and the lateral constant (Poisson's ratio ? = 0.3). Estimate the change in length in the vertical, horizontal and diagonal sides as well as determine the volumetric strain. Illustrate the effect of two-dimensionalstrain by constructing appropriate sketches (before and after deformation).Repeat the analysis for lower value of pressure and higher value in the range of [20 -100 MPa] and comment on the overall results
13 t Oy lanmadı Ot izerinden enmiş Txy ruyu e Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as oy=67,9 MPa, oy=25,5 MPa and Ty=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the normal stress on (MPa).
Example vacuum pressure): A thick cylinder of inner radius 8cm and outer radius 12 cm is subjected to an external pressure of -0.09M Pa. Internal pressure is atmospheric. Determine (a) the radial and tangential stress distribution across the the thickness, (b) the axial component of stress, if the ends of the cylinder are fixed. Assume v=0.3 and (c) maximum shear stress
nc./Johan H σy 7.2-1 The stresses on the bottom surface of a fuel tanker (figure part a) are known to be o = 7750 psi, = 1175 psi, and 7 xy = 940 psi (figure part b). Determine the stresses acting on an element oriented at an angle = 55° from the x axis, where the angle is positive when counterclockwise. Show these stresses on a sketch of an element oriented at the angle 0. (a) PROBLEM 7.2-1 (b) 1175 psi Ţ 940 psi 7750 psi 7.2-5 The stresses acting on element A on the web of a train rail (see figure part a) are found to be 6500 psi tension in the horizontal direction and 18,500 psi com- pression in the vertical direction (see figure part b). Also, shear stresses with a magnitude of 3800 psi act in the directions shown. Determine the stresses acting on an element ori- ented at a counterclockwise angle of 30° from the horizontal. Show these stresses on a sketch of an ele- ment oriented at this angle. Cross Section (a) PROBLEM 7.2-5 B A Side View A (b) 18,500 psi 76500 psi 3800 psi
2. A square plate in the side of a ship with 800 mm sides parallel to the x and y axes has a uniform thickness h=10 mm and is made of an isotropic steel (E=200,000 MPa and v-0.29). The plate is subjected to a uniform state of stress. If o 0=02y=0 (plane stress), Oxx= 01=500 MPa, and ɛyy-0 for the plate, Determine oy=02, 03, and the three final dimensions Lx, Ly, and L, of the plate, assuming linearly elastic conditions.
pru 7 Oy enüz žvaplanmadı Ot .00 üzerinden aretlenmiş Txy Soruyu aretle Ka Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the maximum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
Current Attempt in Progress Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are 5x = 36 MPa, Sy = 87 MPa, and Sxy = 25 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Answer: (a) Op1 = Op2 = Tmax in-plane Sxy (c) Tmax abs MPa MPa MPa (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) MPa
1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below, whose geometry and the applied force are known. 200 mm d = 30 mm 5000 N 5000 N t= 25 mm r= 15 mm
Please help me with this , i really can't thank you enough
The prismatic bar shown below has a solid circular cross section with a 2 in. radius.(a) Calculate the average normal stress at P1 and (b) Calculate the average normal stress at P2.