3. A single-phase 50 Hz generator supplies an inductive load of 5 MW at a power factor of 0-866 lagging by means of an overhead transmission "line 20 km long. The line resistance and inductance are 0:0195 ohm and 0:63 mH per km The voltage at the receiving end is réquired to be kept.constant at 10 kV. (a) Find the sendingend voltage and voltage regulation of the líne.

3. A single-phase 50 Hz generator supplies an inductive load of 5 MW at a power factor of 0-866 lagging by means of an overhead transmission "line 20 km long. The line resistance and inductance are 0:0195 ohm and 0:63 mH per km The voltage at the receiving end is réquired to be kept.constant at 10 kV. (a) Find the sendingend voltage and voltage regulation of the líne.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In your own word please help
Solve how to get D and E d. 667.66216 MW, 123.6162 MVAR (cap), 679.00937 MVAe. 32.33784 MW
Q1: A 3-phase of sequence ABC transmission line has a conductors of cross section area (82 mm?) and a diameter of (1 cm) as shown in figure below. Delivers a load of 15 MW at 30 kV and power factor of 0.78. Determine the efficiency and voltage regulation of the line. If the line length (65km). The line is completely transposed. For the copper p = 1/58 per meter length. 3 m 4 m 6 m 4 3 m
Please neglect the simulation
In single phase overhead transmission lines, the increase of the line resistance leads to an increase of: Select one: a. All of the above O b. None of the above c. The losses O d. The load voltage
A 400 km long, 50 Hz transmission line having series resistance and inductance of 0.12/km and ImH/km, and shunt capacitance of 0.01µF/km connects a generator and a load. The load is consuming 100 MW at 220 kV and 0.8 power factor lagging. Find the voltage and current at the sending end, and the voltage regulation of the line. Assume distributed parameter model of the line.
2. A balanced load of 30 MW is supplied at 132 kV, 50 Hz and 0-85 p.f. lagging by means of a transmission line. The series impedance of a single conductor is (20 + j52) ohms and the total phases-neutral admit- tance is 315 microsiemens. Shunt leakage may be neglected. Using the nominalT approximation, calculate the line voltage at the sending end of the line. If the load is removed and the sending end voltage remains constant, find the percentage rise in voltage at the receiving end.
12. Revi i. What difference you noticed in voltage regulation between RL and RC Loads? Why? i. Maximum voltage regulation occurs when power factor is In the case of inductive loads, for a fixed value of VR and I, the voltage regulation of the line increases with the ii. in power factor. iv, What are main reasons for voltage drop in transmission line?
Question 6 please
* Find the current through the diode in the circuit shown. Assume the diode to be ideal. 50 92 A R₁ V= 10 V 185 mA O 46 mA 140 mA 28 mA wwww 5923 R₂ B D
If a 3-phase short circuit occurs in one of the two circuit of transmission line at point F, and the shunt impedance of the short circuit is j0.1 pu. Determine the maximum time when a short circuit can still be cleared. So=0.8+j0.3 Xd'= 0.2, XL1=XL2= 0.6, XT1=0.12, Xr2= 0.1, L1 V= 1.0 T1 L2 F T2 .XL= 0.1 Хс- 0.1. S1 S2 SL= 0.6+j0.3