3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm]

3. A seamless steel pipe carries 2000 m³ of steam per hour at a pressure of 1.2 N/mm². The velocity of flow is 28 m/s. Assuming the tensile stress as 40 MPa, find the inside diameter of the pipe and its wall thickness. [Ans. 160 mm; 5.4 mm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Example: What is the pressure at the center of the pipe B?
The volume flow rate of water is 669,3 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C) Length D-0 07 m <-0.08 mm Elevation 650 m Elevation 653 m
I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The then breaks into N narrow Pipes (which have a diameter, d2, and a length, L2), before the water is released to the atmosphere, as shown in the figure. The entrance to the small pipe from the large pipe has a loss coefficient of KL. You may assume the flow is laminar and fully developed everywhere in the system, and that any changes in height are neglible. (The viscosity is NOT negligible) a) Find an expressin for the velocity of water leaving the sprinkler b) Find an Expression for the gauge pressure at point A, a distance L1 upstream of the narrow pipes. Express your answer in terms of the flowrate, Q. c) The inner diameter of the first segment of the pipe is d1 = 10mm, the inner diameter of the second set of pipes is d2 = 1mm, with N = 25. The flowrate through the sprinkler is Q = 0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds…
The sprinkler system is used for watering the garden as given figure below Working fluid enters the system at 9,26 liters/s. Calculate the required torque [N.m holding the system as stationary for 0-30°. (NOTE: Take P1000 kg/m)
Find the initial velocity Final velocity=5 m/s Accelertaion=2 m/s2 time=2-s
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
Find the initial velocity Final velocity=5 m/s Accelertaion=2 m/s2 time=3-s
The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m) 05 m 95 kPa 100 kPa Pump
62.4¹,Mw lb Water (Yw ft³ an average velocity of 5 ft/s. Find the change in pressure over 39 ft of pipe. Provide your answer in = D 23.6 x 10-6 ) flows through the 4-in. diameter pipe below with -6 lb-s ft² lb ft² The pipe has roughness of 2x10-4ft. L
Water is flowing steadily at an average velocity of 6 m/s in a pipeline of diameter 50 mm. Somewhere along the pipeline, the diameter of the pipeline is reduced by a fitting to a diameter of 20 mm. Calculate the average velocity of flow in the 20 mm diameter section of pipe. [Answers in m/s, Numerical value only] Answer: Next page OSearch for anything
Question 3 A pipe of 150mm bore is delivering water at the rate of 7500 dm/min at a pressure of 820 kN/m?.It connects by a gradually expanding pipe to a main of 300 mm bore which runs 3m above it. Find the pressure in the 300mm main?
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?