3. A 0.180 A, 10 V stepper motor is applied to the terminals with a no-load speed at 12,000 rpm. The proportionality constant relating current to torque load is the torque constant kM = 1.040 oz- in/A. Given the motor efficiency at 70% and torque ratio of 0.5, determine the a. resulting motor speed b. torque load, c. motor current, d. the mechanical power input and output

3. A 0.180 A, 10 V stepper motor is applied to the terminals with a no-load speed at 12,000 rpm. The proportionality constant relating current to torque load is the torque constant kM = 1.040 oz- in/A. Given the motor efficiency at 70% and torque ratio of 0.5, determine the a. resulting motor speed b. torque load, c. motor current, d. the mechanical power input and output

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A dc shunt motor developes 10 HP at 8000 rpm when drawing a line current of 40 A at 220 V. Find the efficiency at this load and the useful torque.
A 240 V, compensated shunt motor driving a 1233.96 N.m torque load is running at 19.167 rps. The efficiency of the motor at this load is 94 percent. The combined armature, compensating winding and interpole resistance is 0.00707 ohm, and the resistance of the shunt field is 52.6 ohm. Determine the following parameters of the motor: (i) Input power (in kW) (ii) Field current (in Amp) (iii) Armature current (in Amp) (iv) Induced voltage in armature (in volts) (v) Torque developed by motor (in N.m) and (vi) The resistance of a dynamic breaking resistor (in ohm) that will be capable of developing 678 N.m of braking torque at a speed of 16.667 rps. Assume windage and friction at 16.667 rps is the same as at 19.167 rps. [Hint: 1 lb-ft = 1.356 N.m]"
A 400 V series motor has a field resistance of 0.02 ohm and an armatureresistance of 0.1 ohm. The motor takes 30 A of current at 1000 rpm whiledeveloping full load torque. What is the motor speed when this motordevelops 60 % of full load torque and the shunt is shunted by a resistorof 0.03 ohm? [Ans. 1294.98 rpm]
A220 Vshunt DC motor rotates with speed of1800rev/min.( need handwritten only ,otherwise downvote.)
w3
Qa/ a- Explain the difference in the Torque-Speed Characteristics of DC Shunt and series Motors. b+ A 120 V shunt motor has the following parameters: Ra = 0.4 0, RF = 120 Q. On full load, the tine current is 19.5 A and the motor runs at 1200 rpm, find the output torque.
Question4 A 120-V series motor runs at 2000 rpm at full load and takes a current of 12A. The armature resistance is 0.3 ohms and the series field resistance is 0.2 ohms. A diverter resistance of 0.2 ohms is connected across the series field, and the load on the motor is adjusted. If the motor now takes 20A, what is the new speed of the motor, determine the torque developed in each case.
3 decimal places
A240 V d.c. series motor takes 40 A when giving its rated output at (500 r.p.m.its total resistance is 0.32.Find what resistance must be added to obtain rated torque i) At starting
A 440 volt d.c. The armature resistance of the motor is 0.25 ohm. It takes an armature current of 60 A at 750 RPM. So find the value of torque produced in the motor.
An armature controlled DC motor has the following parameters: Tf = 0.03 Nm KT = 0.15 Nm/A Imax = 2.4 A KĘ = 0.15 Vs/rad Wmax = 5000 rpm R = 0.8 Ohms 1. Determine the following: (i) The maximum output torque. (ii) The maximum power output. (iii) The maximum armature voltage. (iv) The no load motor speed when e = Emax 2. Plot the following relationships: (i) Torque versus current (ii) Induced voltage versus speed 3. If the above motor is operated at 3000 rpm with a load torque of 0.15 N.m, determine the armature voltage
A 240V , Shunt DC - motor delivers power to a load at 1200 Rev / Min . The load Torque drawn by the motor is 320 N.m. The armature %3 resistance is 0.3 Ohm and the field resistance is 100 Ohm and the rotational losses are 500W. a. What are the armature current and the efficiency ? b. If the torque decreased to be 250 N.m find the speed !