3- Given the impuls response, please examine the causality and stability of this linear time invariant system (whether its stable or unstable in BIBO sense). What will be the y[n] if the input is x[n]= (1/2)"-lu[n] ? State your answers with explanation. h[n] 1 -1 -2 1 2 3 n -1 3.

Q: Use ONLY 1-to-4 demultiplexers to implement a 1-to-8 demultiplexer. Avoid any redundancy by clearly…

A:

Q: Immediately after a reset, CS=FFFF and IP=_______. (Give four hex digits.)

A: Ans :-  0000H

Q: Based on the given signals of f[n] and g[n] in Figure 1, sketch the operation of the signals s…

A: Given: spectrum of F(n) and g(n) Find the above questions

Q: Classify each of the following as serial data (A) or parallel data communication (B). Type of action…

A: (i) In serial communication, the data is sent one bit at a time while in parallel communication…

Q: (a) The varable yesistoe in the CirCuit of Fil below ie adjnsted for Max power transer to Ro. Finod…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Identify the type of signal as shown on the following figures. Also, indicate the equation defining…

A:

Q: It is most likely to affect the signal in the channel. a. Cable b. Noise c. Input date d. Free-space

A: There are various factors that affect a channel. Noise is referred as a unwanted signal.

Q: lo avold corruption during transmission, the code-word snould be Select one: O a. None of the…

A: The code-words should be far apart from one and another as possible  So even when the vectors…

Q: what will be the value of e^infinity?

A: The solution is given below

Q: estion 4 ruction for each group of fallowing instructions Assuming no forwarding or hazard…

A: Assuming no forwarding or hazard detection, add the suitable number of NOP instructions for each…

Q: please could give a simplified drawn schematic/diagram to show a how  microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: Could someone explain the solution picture 1 with the 'OR'. The solution is on picture 2 but I want…

A: According to the question, for the given circuit as shown below We need to explain the problem…

Q: An indicator is an instrument that is a(n) ____ -loop device. open O closed

A: In this question we need to choose a correct option

Q: The energy per bit to noise ratio for the following parameters is______________. C=1nW, N=1pW,…

A: In this answer we will find the Eb/No i.e. energy per bit to noise ratio as shown below.

Q: Telegraph system has two symbols (dot, dash), assume time of the dot symbol equal 0.2 sec ad the…

A:

Q: Complete the number conversions indicated. Note that all binary numbers are two’s complement…

A: A binary number is a number which is expressed in base-2 system by using only "0" or "1" digits.…

Q: For what purpose we use the Ohm's 2 option in IT intellitone 200 probe transmitter?

A: Purpose of Ohm's symbol in IT intellitone 200 probe transmitter :- The ohm's symbol is used in IT…

Q: What frequencies found in RTK radios require licensure?

A: As per the code of federal regulations, it holds the complete rules of FCC. The federal regulations…

Q: Match each of the following terms with its be description. DRAM SRAM NV-RAM EPROM A. Uses floating…

A:

Q: Question 15 Covert (521) from base 8 to base 11

A:

Q: using 1s comiPlement C\ool ~Cい001) =( ?っ Gvay Exー3

A:

Q: What is the name and function of this symbol?

A:

Q: How many select lines would be required for an1-line-to 8-line demultiplexer? a) 8 b) 2 c) 3 d) 1

A: We need to find out select lines for given demux .

Q: DSB-SC (generartor/modulator) m4+cosakk NLD +) Coshet -m) |NLD find , & and . 'NLD= Non - Unean…

A:

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: The data recording space on magnetic tape between the blank intervals is known as a/ an: Block…

A: Magnetic tape- The magnetic tape is coated with a material (iron Oxide or Chromium diode) that…

Q: QUESTION 19 The program which handles an interrupt is called the: O BIOS Int ox ISR IRQ QUESTION 20…

A: Dear student as per guidelines we are allowed to answer only first 3 MCQ, but for you I have…

Q: acity of a Communication C

A: Given: The answer is shown as:

Q: T lines are designed for Digital data how they can be used for Analog Transmission?

A: Digital Transmission of analog information is possible if a minimum level of signal to noise is…

Q: For Q4 (i) and similar thing to (ii) and (iii) When calculating ni1/ni2 = (300/293.15)^1.5 I got…

A: Q. 4)(i) with respect to the calculation of ni1/ni2 = (300/293.15)^1.5

Q: _______________________ register can be used to store base address. a. IP b. SS c. BP d. SP

A: The explanation is as follows.

Q: What does {4||1} mean? Am I using node analaysis?

A: Given an electrical circuit, asked to find the IR4as a follow-up question, asked for the meaning of…

Q: QUESTION 45 The offset address is bits wide.

A: The address and registers are the terms used in a microprocessor.every data has its location where…

Q: The circuit that causes one signal to modulate another is called a(n) _____.

A: The circuit that causes one signal to modulate another is called modulator,the two signals applied…

Q: Question 13 NMI is Non- Interrupt.

A: NMI: It computing, it is a hardware interrupt which can't be ignored by the standard…

Q: a. None of the mentioned b. On-off c. Unipolar RZ d. RZ-AMI

A: In RZ AMI three levels are used  Which are positive negative and return to zero. So a extra zero…

Q: Is there anything particularly noteworthy about a CPLD?

A: To do:We need to mention some noteworthy points about a CPLD.

Q: 12 A discrete relay type output module can be used to switch either AC or DC load devices. Why? OIt…

A: Relay:- An electrically controlled switch is a relay.  It is made up of a set of working contact…

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.