12 A discrete relay type output module can be used to switch either AC or DC load devices. Why? OIt uses complex circuitry to convert AC signals to DC signals so that it can handle either type of output. O All output cards can be utilized across various types of loads, without concern for voltage type or amplitude. OIt uses an electromechanical relay element for switching which allows it to work for either AC or DC applications. O Since AC is just an alternating form of DC, all AC output modules can be utilized for switching either AC or DC. QUESTION 13 Explain the purpose of a redundant PLC processor. O It allows the output modules to carry more current by utilizing two or more PLC's O It allows one processor to carry out one task on the same equipment and the other to carry out a different task on the same equipment It is a great way for the installer to double their installation costs O It allows transfer of control to the second processor in the event of a processor fault.

12 A discrete relay type output module can be used to switch either AC or DC load devices. Why? OIt uses complex circuitry to convert AC signals to DC signals so that it can handle either type of output. O All output cards can be utilized across various types of loads, without concern for voltage type or amplitude. OIt uses an electromechanical relay element for switching which allows it to work for either AC or DC applications. O Since AC is just an alternating form of DC, all AC output modules can be utilized for switching either AC or DC. QUESTION 13 Explain the purpose of a redundant PLC processor. O It allows the output modules to carry more current by utilizing two or more PLC's O It allows one processor to carry out one task on the same equipment and the other to carry out a different task on the same equipment It is a great way for the installer to double their installation costs O It allows transfer of control to the second processor in the event of a processor fault.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

h.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.
14. A 200-ampere, 120/240-volt, single-phase service is required to supply a single-family dwelling. The NEC permits these conductors to have ampacity not less than ? of the service rating. Oa. 0.73 A Ob. 0.75 A Oc. 0.83 A Od. 0.85 A
A 636 kcmil 26/2 ACSR conductor has a GMR of _____ inch at 60 Hz. (Round-off answer in 3 decimal places)
2023
Please answer in typing format
8. Parallel conductors must be installed in sizes no smaller thanA. 1/0.B. 2/0.C. 750 kcmil.D. 4/0.
Analyse several voltage and current situations in different loading scenarios in a simplified radial (transformer to consumption) medium-voltage power system example. There are only 2 nodes in the 35 kV line – node 0 from the 110/35 kV and node 1 with one consumer. The physical characteristics of the line and the loading scenarios are individualized for each student – please see the attached file Excel “WM9P3 Task1 data” for your particular data set. Briefly reflect on the complexity of the calculations for known input or output voltage, as well as for fixed or voltage-dependent consumption in this simple power system model. Analyse and discuss the sensitivity of the voltage drop [in % of amplitude and the degrees of phase] with respect to the current level [in %] and to the power factor.
1: Answer only one of the following: A- What are the advantages of a diesel power station? B- Several points should be taken into account in the selection of the site for the Nuclear power station. State these points.
Marked out of 1.50 P Flag question 13. i) The data for a wind turbine is given below: Wind speed = 14 meters/sec, Length of blade = 10 meter. Choose the correct statement for this wind turbine. a. The input wind power to the turbine is 258 KW b. The input wind power to the turbine is 51.7KW c. The input wind power to the turbine is 25.8KW d. The input wind power to the turbine is 517KW 13. ii) Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 40square meters. b. The wind rotor swept area is 62.4 square meters. c. The wind rotor swept area is 314 square meters. d. The wind rotor swept area is 31.4 square meters. O O O O
5
11 and 12 , i need this answer
1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above.