3) An 8086 based system is interfaced to memory to read 16 bit data. What are the contents on the databus when the processor is reading the variables px, py and pz during memory read cycles. List them in a table as below. Variable D15-D8 .model tiny Org 2000h Px db 3; Py dw 2130h EVEN Pz dw 3456h -- Mov al,px Mov ax.py Mov ax,pz D7-D0

3) An 8086 based system is interfaced to memory to read 16 bit data. What are the contents on the databus when the processor is reading the variables px, py and pz during memory read cycles. List them in a table as below. Variable D15-D8 .model tiny Org 2000h Px db 3; Py dw 2130h EVEN Pz dw 3456h -- Mov al,px Mov ax.py Mov ax,pz D7-D0

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Help me with these computer architecture questions, please. I need help with questions 1 and 2.
The content of the stack pointer SP is 3560, and the register PC contains the value 2000. The location 2000 contains the two word instruction BSR 2500. Given that the size of the stack frame is 4 bytes, and that each instruction(along with the data it uses) is 4 bytes long, what is the value contained in SP immediately after the BSR instruction is executed? Select one: а. 2500 O b. 3556 O C. None of these choices d. 2004 O e504
Q.In a computer instruction format, the instruction length is 11 bits and the size of an address field is 4 bits. Is it possible to have 32 zero-address instructions using the specified format? Justify your answer.
On a typical microprocessor, a distinct I/O address is used to refer to the I/O data reg- isters and a distinct address for the control and status registers in an I/O controller for a given device. Such registers are referred to as ports. In the Intel 8088, two I/O in- struction formats are used. In one format, the 8-bit opcode specifies an I/O operation; this is followed by an 8-bit port address. Other I/O opcodes imply that the port ad- dress is in the 16-bit DX register. How many ports can the 8088 address in each I/O addressing mode? .
is stored in the memory starting 2- The ISR address of interrupt number at address (0039CH). 3- In the instruction: (MOV AL,[3AFH]), data is transferred to 8086Mp over data clock cycles. lines: using 4- In the instruction: (MOVAX,[5BC2H]), data is transferred to 8086Mp over data lines: clock cycles. using
Help me with these computer architecture questions, please. I need help with questions 3 and 4.
ans fast
Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:
Draw the complete block diagram for an 8086 Microprocessor system with two PPIS, where the address (PA/PPI1)-82H and the address (PA/PPI2)=83H. Then, write a program to read 64 bytes from the PA&PB of PPII and display them on PPI2-ports in the right sequence using mode 1.
microprocessor 8086