On a typical microprocessor, a distinct I/O address is used to refer to the I/O data reg- isters and a distinct address for the control and status registers in an I/O controller for a given device. Such registers are referred to as ports. In the Intel 8088, two I/O in- struction formats are used. In one format, the 8-bit opcode specifies an I/O operation; this is followed by an 8-bit port address. Other I/O opcodes imply that the port ad- dress is in the 16-bit DX register. How many ports can the 8088 address in each I/O addressing mode? .

On a typical microprocessor, a distinct I/O address is used to refer to the I/O data reg- isters and a distinct address for the control and status registers in an I/O controller for a given device. Such registers are referred to as ports. In the Intel 8088, two I/O in- struction formats are used. In one format, the 8-bit opcode specifies an I/O operation; this is followed by an 8-bit port address. Other I/O opcodes imply that the port ad- dress is in the 16-bit DX register. How many ports can the 8088 address in each I/O addressing mode? .

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

(d) The table below shows the ALUcontrol signal of the datapath we discussed in class. Instruction Funct ALU Орсode ALUop ALU action operation field control Iw 00 load word XXXXXX add 0010 Sw 00 store word XXXXXX add 0010 beq 01 branch equal subtract 0110 XXXXXX R-type 10 add 100000 add 0010 R-type 10 subtract 100010 subtract 0110 R-type 10 AND 100100 AND 0000 R-type 10 OR 100101 OR 0001 R-type 10 set on less than 101010 set on less than 0111 You want to add the bne instruction into the datapath, which already includes the required hardware for the instruction. Write out the ALUop for bne and how you can determine whether the bne results in the branch to be taken.
Computer Science Y86-64 Question 2: Try to write the machine code encoding of the assembly instruction. mrmovq 0x15F(%rbx), %rax Tips: It has a little-endian byte ordering. Please show the full steps.
microprocessor 8086
2. Memory contents (in hexadecimal) are 0005, 0001, 0123 for addresses 000 to 002, then 2002, 1000, 7800, F400 for addresses 80A through 80D. AC starts with value 0F24, PC has the value 80A, and AR has the value 4F5. Starting with time-step T0, describe what happens until the next TO. Make sure to indicate any updated register values as they happen. (Assume R= 0.) Refer to table 5.6 from Mano's textbook. F24 1 AR
The loop instructions transfer execution control to another point designated by the instruction pointer. (ip) O (ecx) + sign extended 8-bit displacement (ip) + sign extended 8-bit displacement O (ip) + unsigned 8-bit displacement O (ecx) + unsigned 8-bit displacement
Digital system design
Separate data groups are represented by each individual element of the table that lists the interrupt vectors.
Micro processor 8086 Assume that there are two bit 32-bit numbers:4444DDDDH and CCCC0003H .write an assembly program program to sum them , if it’s possible to do it with intel 8086 microprocessor then cross check (4444DDDH and CCCC0003H
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. A - is for addressing mode type, e.g. direct B - physical address/es e.g. 19000-19001 C - content of the destination after execution e.g. if register: AX=1234 if memory (lower address first): 12000=34,12001=12 GIVEN AX =AD6EH DX = 9ECFH SS = BEDAH SI = AECDH BX =AFECH CS = EBDCH ES = CFEDH BP = EFBAH CX =FADEH DS = AF0EH DI = BD8FH IP = AB8FH
witch of the following is the mode of addressing specifies the index of a register where the value of interest is located: A immediate addressing B pseudo-direct addressing C base (or displacement) addressing D register addressing E PC-relative addressing
A computer system interfaces a memory with a 32-bit address bus and a 16-bit data bus. The memory addressing is performed using a decoder. What is the number of AND gates needed to implement the decoder? What is the FAN OUT of the decoder?
Do please