3: A steel pole is used to hold a triangular banner as shown. At its base, there are 8 bolts spaced equally around a bolt square. The corner bolts (1, 3, 8, 0) have a diameter of 25 mm each while the center bolts (2, 4, 5, 6, 7, 9) have a diameter of 10 mm each. The shear modulus of the pole is 80 GPa. If the wind pressure is W = 9.3 kPa, determine the following:

3: A steel pole is used to hold a triangular banner as shown. At its base, there are 8 bolts spaced equally around a bolt square. The corner bolts (1, 3, 8, 0) have a diameter of 25 mm each while the center bolts (2, 4, 5, 6, 7, 9) have a diameter of 10 mm each. The shear modulus of the pole is 80 GPa. If the wind pressure is W = 9.3 kPa, determine the following:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B2
i need the answer quickly
Please don't provide handwritten solution .....
Mo = M-400×0.15cos30-320x 0.3 = 0 160 mm 400 N M = 148 Nm CCW Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N 250 mm 250 mm 250 mm 125 mm 240 N
Q4
A cable is enacting a force, F, on a built-in hook at an angle 9 as shown in the figure. Determine the displacement of the point at which the force acts, in the direction of the cable if the shaft of the hook has a length L, radius r and elastic modulus E. Ignore the deformation of the circular hook. If E= 200 GPa, F = 50 kN, 0 = 25°, L = 1 m, r- 100 mm: Answer: 8 = 0.196 mm
A hydraulic punch press is used to punch a slot in a 0.30-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 36 ksi, determine the minimum force P required to punch the slot. Assume d = 1.25 in. and a = 2.25 in.
Construct the reduced stiffiness matrix of the shown truss, Fig. 3.Then determine the nodal displacements and the nodal forces in clement 3. L(1) L(2) 2 m, L(3) 2/2, A(1)- A(2) = A(3) = 80 mm2, and E= 200 GPa. |1 (1) 2 2 kN '3 kN (2) 45° (3) 3 Fig. 3
PROBLEM 2. The carrier system in the figure consists of the AB rigid beam and two aluminum bars and a steel bar connected to it. After the assembly is created at 20 ° C without causing any prestresses, calculate the stresses on the bars if the temperature is increased to 80 ° C. Steel A-36 A =160 mm2 3,5 m 10 kN/m A 3 m В 3 m 2 m 2014-T6 Aluminum A =200 mm2 E
W=60lbs/ft a=7ft b=5.5 ft
3. If only one person is on the swing in the image below, it is comparable to a point load of F = 500 N placed at x = 0.5 m on a wooden branch embedded at one end (cantilever). The length of the branch is 1.5 m. It is given that I = 1 × 10-6 m² and E = 2x 10° Nm². The boundary conditions are y(0) = 0, y'(0) = 0 , y'"(0) = M and y''(0) = –2M. Use your notes to model the fourth order differential equation suited to this application. Present you differential equation with y'' subject of the equation. Use the Laplace transform to solve this equation in terms of M. Use your solution to determine the value of M at x = 0.5 m where this branch will break (deflection more L than thresh y 2 240 ). Do not use Matlab as its solution will not be identifiable in the solution entry. You must indicate in your solution: 1. The simplified differential equation in terms of the deflection y you will be solving 2. The simplified Laplace transform of this equation where you have made L{y} subject of the…