05. Determine the forces in members DE, DI, and JI of the arched roof truss shown below. ¢4>6 6*4> 4 6 6→4> | 100 kN 75 kN 75 kN D 25 kN- E 25 kN 3 МЕMBER FORCE (kN) DE F B DI JI K H 14 G Dimensions in meters

Q: Reflection: Be sure to understand where along the span length the greatest flexural normal stress…

A:

Q: KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a…

A: Given : The shear force in this section is The diagram is,

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: How is the shear flow, measured?

A: Shear flow: The shear flow in solid mechanics is a terms on multiplication with thickness which…

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: Why should the selected section modulus, be slightly greater than Sreq>d?

A: Generally, section modulus is calculated by considering external loads only. So in order to account…

Q: 10 1 R6 1 10 20 50 30 R10 -5 X 45.00° 50 1 1 5 15 5 R30 110 R5 55 20 R6 7 8 60 30 -60 店 06-4 holes…

A: Step 1: First create following top view and extrude it up to required depth i.e. 60 mm

Q: What are Shear and Moment Diagrams?

A: Shear and moment diagrams are investigative tools that are utilized for structural analysis in order…

Q: How can the internal moment be determined?

A:

Q: Filler rod material is same base metal used in gas welding process. Select one: True False

A: Above statement is true.

Q: What is the Positive internal moment?

A: Whenever a beam is subjected to the bending moment, axial stress develops in the fibre of the beam.…

Q: Clok on "add vertioal line off to add dicoontinulty linec. Then ollok on "add cagment" button to add…

A: To draw SFD and BMD

Q: Industrial pipes Expansion joints are fragile elements and therefore should be avoided…

A: The objective of the question is to understand when to use expansion joints in industrial piping…

Q: On the part attached, what is the flatness on the top surface with only the profile applied? And…

A: from the given the top surface flatness must be within  0.4 tolerance zone with respect to bottom…

Q: 110 About indistrial piping WHY IS THE ASME 31.3 ALLOWABLE STRESS A COMBINED STRESS?

A: The objective of the question is to understand why the ASME 31.3 allowable stress is a combined…

Q: How can the direction of shear flow be established?

A: In solid mechanics, the shear flow is defined as the flow when the transverse shear force acts on a…

Q: Please answer the attached question. Please note that I have sourced the required background…

A: The objective of the question is to find the value and location of the largest tensile and…

Q: What is the negative internal moment?

A: Generally, a component or beam is subjected to three types of force, such as normal force, shear…

Q: What does the moment-area method provide?

A: Solution:

Q: How is the internal strain energy within a beam caused?

A: Strain energy: When a system undergoes a stress and rearranges itself due to deformation, the energy…

Q: How is the shear center determined?

A: Shear Center The shear center is a point on the section of the beam, from where the resultant load…

Q: What steps should be taken to obtain The resultant internal loadings at a point located on the…

A: The internal loading are the forces and the moments that are applied by the half of the section on…

Q: Engineering drawing Find, top section, side section and front section?

A: