3 A simply supported 18 m effective span RCC rectangular beam of 500 mm x 1500 mm (overall deptn) section is reinforced throughout with 21 numbers of 25 mm diameter bars in three layers of 7 bars each at a clear cover of 37.5 mm on tensile face. The reinforcement in the compression face is 4 numbers 25 mm diameter and 1 number 20 mm diameter bars in one layer at an effective cover of 50 mm. The clear cover between the different layers on tension face is 25 mm. M25 grade concrete and Fe 415 grade steel bars are used in the beam throughout. The beam is laterally restrained throughout the span. (a) Find out the maximum bending moment M, at limit state of collapse for the beam section assuming the stress in compression reinforcement o = 0.9566 f, corresponding to tensile stress f, in tensile reinforcement at the limit state. (b) What should be the superimposed uniformly distributed load 'w', the beam can carry at working conditions? (c) Design the shear reinforcement at support if design shear strength of concrete t, is given as 100A, follows for different values of p = bd 1.25 1.5 1.75 Te, MPa 0.70 0.74 0.78 D0041

3 A simply supported 18 m effective span RCC rectangular beam of 500 mm x 1500 mm (overall deptn) section is reinforced throughout with 21 numbers of 25 mm diameter bars in three layers of 7 bars each at a clear cover of 37.5 mm on tensile face. The reinforcement in the compression face is 4 numbers 25 mm diameter and 1 number 20 mm diameter bars in one layer at an effective cover of 50 mm. The clear cover between the different layers on tension face is 25 mm. M25 grade concrete and Fe 415 grade steel bars are used in the beam throughout. The beam is laterally restrained throughout the span. (a) Find out the maximum bending moment M, at limit state of collapse for the beam section assuming the stress in compression reinforcement o = 0.9566 f, corresponding to tensile stress f, in tensile reinforcement at the limit state. (b) What should be the superimposed uniformly distributed load 'w', the beam can carry at working conditions? (c) Design the shear reinforcement at support if design shear strength of concrete t, is given as 100A, follows for different values of p = bd 1.25 1.5 1.75 Te, MPa 0.70 0.74 0.78 D0041

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
Given a rectangular section of b = 300mm, h = 400mm, a, = a', = 40mm; the concrete is of grade C30, the steel is HRB400. Find the reinforcement (A, and A') required for a load of M = 218kNm and an axial compression N= 396KN. %3D
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in negative bending.
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
Design the T beam for the floor system when subjected to an ultimate moment of 300 kN-m. Beam span is 6m, beam width is 300 and d is 450mm. fc = 30 MPa, fy = 420 MPa. Determine the effective width of the T-beam in mm. Is the compressive flange adequate enough to provide the design capacity required? How many layers/rows of steel rebars are expected in the design of reinforcement? How many 25mm steel bars are required for the section?
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side
Design Problem 5 Determine the spacing of 10 mm U Stirrups required for the beam of design problem 4.0 at Ls = 1.10 m from the support if fpu is 1,724 MPa for the prestressing steel and fy for the stirrups is 276 MPa. Aps = 945.16 mm² (Use NSCP Equation, Table 409.6.3.3e)
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D
3-2 A rectangular section with width b=200mm and depth h=450mm is to carry a design bending moment M=145KN •m. The concrete is of grade C40 and the tensile steel is of HRB400. The tension reinforcement A, is required.
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)
DETERMINE THE CONCRETE AND STEEL STRESS AT THE FIXED SUPPORT C.