9-23. The wood beam is subjected to a load of 12 kN. If a grain of wood in the beam at point A makes an angle of 25° with the horizontal as shown, determine the normal and shear stress that act perpendicular and parallel to the grain due to the loading. y

9-23. The wood beam is subjected to a load of 12 kN. If a grain of wood in the beam at point A makes an angle of 25° with the horizontal as shown, determine the normal and shear stress that act perpendicular and parallel to the grain due to the loading. y

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

The steel channel is used to reinforce the wood beam. Determine the maximum stress in the steel and the wood if the beam is subjected to a moment of M=1.2kN.m Est = 200GPa, Ew = 12GPa. 12mm A 3.'S. IO. **** SI TEMININING FEMININ... *** 12mm INI MINI SEUR 5.1.3. TE 2277 *** ....... ---- 175mm 100mm 12mm 1.2kN.m
I will rate immediately, thank you!
Flexure stress *please answer in complete solution and Draw the FBd properly and neatly *
GIVEN: Solid alumınum bar shown: 4 in. by4 in. E = 10 x 10° psi oy = 36 ksi 4000 2000 1b 4000 16 B 12' REQ’D: A) Load in each section of the bar (state whether C or T) PAB = Pac PCD = B) Maximum axial stress in the bar. In which section does this occur? C) Final length of the bar
Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 150MPa and the allowable bearing stress for the wood is 28MPa. Assume that the hole in the washers has the same diameter as the bolt. -2 m- 3 kN 2 kN 1.5 kN 2 m--1.5 m-1-1.5 m-1-1.5 m--1.5 m- B D
9-22 The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an angle of 25° with the horizontal as shown, determine the normal and shear stress that act perpendicular and parallel to the grains due to the loading. 9-23 The wood beam is subjected to a distributed loading. Determine the principal stresses at point A and specify the orientation of the element. 12 kN -2 m 1 m- 4 m 25° 75 mm 300 mm 200 mm
Two pieces of wood are glued together, find the maximum load which the glued wood could carry that must not exceed 12 MPa normal stress and 7 MPa shear stress. P 30° P 100 mm Glued Section 100 mm
2.6-22 A compression bar having a square cross section with sides b = 50 mm is subjected to load P. The bar is constructed from two pieces of wood that are connected by a glued joint along plane pq that is inclined at angle a = 35°. The allowable stress in the wood in compression is 11.5 MPa and in shear is 4.5 MPa. Also, the allowable stress in the glued joint in compression is 3.5 MPa and in shear is 1.25 MPa. Determine the maximum load P that can be applied to the bar.
The wood beam has a square cross section. Find the smallest allowable cross-sectional dimensions if the working stresses are 8 MPa in bending and 1.0 MPa in shear | 5 kN 2 kN • m A D В +1.0 m –1.0 m →|
2. The manufactured wood beam carries the concentrated loads shown. What is the maximum safe value of P if the working stress in shear is 6 MPa? 20 mm 80 mm |3P 2 m 2 m 70 mm B 160 mm -- NA I = 15.52 × 106 mmª 1.0 m 1.0 m 20 mm
– A joint is made by gluing two plywood gussets of thickness t to wood boards.The tensile working stresses are 1200 psi for the plywood and 700 psi for the woodboards. The working shear stress of the glue is 50 psi. Determine the dimensions’ b and tso that the joint is as strong as the boards.
A beam carrying an allowable actual moment of -38 KN- m is reinforced as shown. If the the concrete is normal weight and f'c = 25MPa and fy = 420MPa. Determine the following: a. The cracking moment of the beam. b. The transformed moment of Inertia. c. The actual tension steel stress. d. Check the stress if it is correct by force checks. mm www.009 4-020 О 140 mm 300 mm 170 mm * 170 mm: ww.08 ✓ 60 mm