3 A plastic plate is held between rigid supports as showi When the plate is subjected to a uniform temperature increase of AT, the compressive stress on an inclined plane is found as 12 MPa. Determine: 19 (a) The shear stress t induced on the inclined plane. (b) The maximum shear stress Tmax and associated normal stresses o'. Given: E= 6 GPa, α = 100 x 10-6/°C, yok AT = 50°C

3 A plastic plate is held between rigid supports as showi When the plate is subjected to a uniform temperature increase of AT, the compressive stress on an inclined plane is found as 12 MPa. Determine: 19 (a) The shear stress t induced on the inclined plane. (b) The maximum shear stress Tmax and associated normal stresses o'. Given: E= 6 GPa, α = 100 x 10-6/°C, yok AT = 50°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W= 150kN is applied.
A rectangular bar having width w = 6.50 in. and thickness t = 1.25 in. is subjected to a tension load P, as shown in the figure. The %3D magnitudes of the normal and shear stresses on plane AB must not exceed 16 ksi and 7 ksi, respectively. Determine the maximum load P that can be applied without exceeding either stress limit. Assume a = 3 and b = 4. A P a b B Answer: P = i kips %3D
For the stress state shown in the figure below, use the Mohr’s circle method to determine (a) the maximum and minimum principal stresses, (b) the orientations of the maximum and minimum principal stresses (c) how the principal stresses on a properly oriented element. (d) Draw Mohr’s circle using a ruler and a compass
Q1: The stresses measured at a point on bone are oy =5 MPa ,o, = -7 MPa and 1,,=2.4 MPa find: 1. The principal strains and maximum shear strain. 2. The strain energy . Knowing that the poisonratio v=0.3 and the unit volume change =5.6x10
please help
An angled strut b = 6.2 in. thick is subjected to a force F = 55 kip and a uniformly distributed load q = 23.5 kip/ft as shown below. Determine the principal stresses at points A, B, and C. (op1) A = (0₂2) A = (pl) B = (p2)B= (pl) c = (p2) c = = 15 in. 10 in. number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) F 12.5 in. -7.5 in.- -12.5 in. ksi ksi ksi ksi ksi ksi q
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, - 10 ksi, S, -39 ksi, and 5x, -24 ksi. (a) Determine the principal stresses (0,1 > 2) and the maximum in-plane shear stress Tax acting at the point. (b) Find the smallest rotation angle #, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: i Opl = p2 = free m i 0₂ = i O ksi. ksi. ksi.
Current Attempt in Progress Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S= 26 MPa, S, = 19 MPa, and Sy = 30 MPa. (a) Determine the principal stresses (o,1 > o,2) and the maximum in-plane shear stress Tmax acting at the point. (b) Find the smallest rotation angle 0, (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: Opl = i MPa. Op2 = i MPa. Tmax = MPa. Op = i
I need the answer as soon as possible
3. A steel rod of 3 cm diameter and 5 m length is connected to two grips and the rod is held at a temperature of 95 °C. Determine the stress in the rod, and the force in the rod if the temperature drops to 30 °C for the following cases a. The grip ends do not yield b. The grip ends yield by 0.12 cm Assume the Young's Modulus of the rod is E = 2×105 MPa, and the CTE is a=12×106/ °C
1. Determine stress distributions of a rotating ring (See the figure below; Angular speed: 0; Mass density: p). a b
member. Problem 1.2-8. A homogeneous bar AB is supported by steel cables at A and B. The cables' diameter is 12 mm at A and 16 mm at B, and both cables have allowable stress of 50 MPa. What is the maximum weight of the bar? B A 7 m 3 m Answer: Wbar = 9,896.02 N %3D