The rigid, horizontal bar ABC is supported by a rigid, weightless link EB and pinned to a wall at A. Link EB is pinned at both ends E and B. Bar ABC is subjected to a triangular distributed load with w = 5 N/mm. C W B number (rtol=0.01, atol=1e-05) L C Consider the following dimensions: a = 759 mm, c = 675 mm, and L = 1687 mm Determine the magnitude of the average shear stress at pin E, TE. The pin at E is in single shear and has cross-sectional area Ag = 58 mm². |TE| = MPa Y

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: ]means the repair work done to keep the system in good working condition.

A: It is required to fill the blank

Q: A Contractor/foreman needs lumber to be used for wooden scaffoldings, the set of lumber can be…

A:

Q: I need help solving these 3 simple parts, if you can not answer all 3 parts then please leave it for…

A: Since there is only two question given so we are answering above two. There is no 3rd question to be…

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: Consider an air-standard Diesel cycle. Operating data at principal states in the cycle are given in…

A:

Q: answer the next part pls

A: From the previous solution: Pitch circle diameter→D=4 inch Number of teeth→T=16 Hence the circular…

Q: solution incorrect resolve again

A:

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: To calculate the maximum allowable stresses in pressure vessels, compute the minimum allowable…

A: Given data, Part A:- Hence, the value of the maximum pressure is 1000 lbs.

Q: In Part a, could you please explain where the 4 comes from on the line before the answer.

A:

Q: Could you solve the last 3 options (c, d, e) please

A:

Q: I have two parts that need to be answered (Multiple Choice). If you can not answer both parts,…

A: In the left side view of the print, there is a horizontal, straight-line segment on the left side…

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

A:

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: Answer in number 7 and 8.

A:

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: Show from the following data taken for the automobile test performed on a 4 cylinder gasoline engine…

A:

Q: organize the answers pls.

A:

Q: Please give the answer as in the format asked

A:

Q: Question attached

A: (a) Relative humidity is the ratio of the partial pressure of water vapour in the mixture to the…

Q: Draw the Mohr stress circles for the states of stress at a point given in the figures below. For (a)…

A: Draw the Mohr stress circles for the states of stress at a point given in the figures below.  To…

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Determine the normal stress at point A. Express your answer to three significant figures and include…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: I need these 3 parts answered. In manufacturing, dimensions often may fall in a range. For example,…

A: 1-In manufacturing, dimensions often may fall in a range. For example, for three-place decimals, the…

Q: Read the questions again. Your answer is not what I'm asking. Please redo it.  where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.