3) A list of anode materials that are considered for use in x-ray generation in an x- ray diffraction experiment set-up are given below along with their Ka and K$ radiation wavelengths. If our only option for an x-ray filter material is Ni, which anode material would provide the ideal x-ray beam? Provide your reasoning, making use of the graph below, showing the wavelength dependence of the mass absorption coefficient of Ni. Table: List of anode materials and wavelengths of their Ka and KB radiations. Cu Co Fe Cr Mo à for Ka (meters) 1. for KB (meters) 1,541E-10 1,790E-10 1,938E-10 2,292E-10 7,099E-11 1,393E-10 1,622E-10 1,758E-10 2,076E-10 6.328E-11 Figure: Wavelength dependence of mass absorption coefficient of Ni. 400 300 K absorption edge 200 1:a 100 0.5 1.0 1.5 2.0 2.5 (u8/zu))

3) A list of anode materials that are considered for use in x-ray generation in an x- ray diffraction experiment set-up are given below along with their Ka and K$ radiation wavelengths. If our only option for an x-ray filter material is Ni, which anode material would provide the ideal x-ray beam? Provide your reasoning, making use of the graph below, showing the wavelength dependence of the mass absorption coefficient of Ni. Table: List of anode materials and wavelengths of their Ka and KB radiations. Cu Co Fe Cr Mo à for Ka (meters) 1. for KB (meters) 1,541E-10 1,790E-10 1,938E-10 2,292E-10 7,099E-11 1,393E-10 1,622E-10 1,758E-10 2,076E-10 6.328E-11 Figure: Wavelength dependence of mass absorption coefficient of Ni. 400 300 K absorption edge 200 1:a 100 0.5 1.0 1.5 2.0 2.5 (u8/zu))

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a silicon crystal at 27° C doped with atoms at a concentration of Na= 10" cm 1- Calculate the conductivity of the sample. Given H, = 800 cm?/V.s. %3D 2- Locate position of Fermi level E, with respect to intrinsic Fermi level E,
1. Calculate position of Fermi level in Si, Ge and GaAs at temperatures 100K and 100OK.
3.2 Calculate the value of n, for gallium arsenide (GaAs) at 7 - 300 K. The constant B- 3.56 x 10" (em "K) and the bandgap voltage E,- 1.42 eV.
1 . 1 Explain the detection process in a pn diode. ( 4 ) 1 . 2 A pn photodiode has a quantum efficiency of 6 4 % for photons of energy 1 . 5 2 × 1 0 - 1 9 � . Calculate the wavelength at which the diode is operating and also the optical power required to achieve a photocurrent of 3 � � at the calculated wavelength. ( 6 ) 1 . 3 A square Si PIN photodiode ( 1 1 0 � � × 1 1 0 � � with a specific detectivity of 4 × 1 0 1 0 � � � 1 2 � operates at a wavelength of 1 5 5 0 nm . The quantum efficiency is 6 0 % . Assume that the dominant noise source is due to dark current noise. 1 . 3 . 1 Calculate the magnitude of the dark current in a 1 Hz bandwidth. ( 6 ) 1 . 3 . 2 Determine the photocurrent. 1 . 3 . 3 Calculate the smallest detectable signal power at this wavelength when the signal bandwidth is 2 5 kHz . ( 4 ) [ 2 4 ]
GaAs and GaP make solid solutions that have the samecrystal structure as the parent materials, with As and P randomlydistributed throughout the crystal. GaPxAs1 - x existsfor any value of x. If we assume that the band gap varies linearlywith composition between x = 0 and x = 1, estimatethe band gap for GaP0.5As0.5. (GaAs and GaP band gaps are1.43 eV and 2.26 eV, respectively.) What wavelength of lightdoes this correspond to?
2.24 InP is doped with ND = 2.0 × 10 15 cm³ and NA = 1014 cm³. Draw the energy band diagram and calculate the location of the Fermi level.
question in photo plz
The design criterion for a typical scanning tunneling microscope (STM) specifies that it must be able to detect, on the sample below its tip, surface features that differ in height by only 0.002 00 nm. Assuming the electron transmission coefficient is e-2CL with C = 10.0 nm-1, what percentage change in electron transmission must the electronics of the STM be able to detect to achieve this resolution?