29. Gamma radiation is bombarding an iron plate as shown in the figure. A con- vection boundary condition of T;= 150 C and h = 200 W/m-K removes heat from the plate. Find the maximum temperature and its location in the plate. Also find temperature at 1 cm from the side facing irradiation and the rate of heat removal from the side not being irradiated. k = 48.5 kW/m K, µ = 24.6 m'.

29. Gamma radiation is bombarding an iron plate as shown in the figure. A con- vection boundary condition of T;= 150 C and h = 200 W/m-K removes heat from the plate. Find the maximum temperature and its location in the plate. Also find temperature at 1 cm from the side facing irradiation and the rate of heat removal from the side not being irradiated. k = 48.5 kW/m K, µ = 24.6 m'.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. The equation for the temperature profile inside a solid cylinder with heat source is: В. Т-Т, A. T = T, =1-(-) T-T %3! 2k C. D. None of them T-T, = (R -r) 2k 7. For surface of very large area, A. radiosity (J)=0 C. Eb=J B. The emissive power of a blackbody Eb=1 D. Eb 0
A 3-in-diameter cylindrical wire is coated in 3 inches of polyethylene insulation. The wire can be modeled as a grey body with an emissivity of .85. Due to the electrical resistance, the wire is at a temperature of 300 degrees Celsius. The insulation is also a great body with an emissivity of .95, at a temperature of 40 degrees Celsius. (Assume F12=1). What is the heat flux (W/m^2) of the energy going from the wire to the insulation?
! Required information Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is reflected from the medium and 130 W/m² is transmitted through the medium, Determine the absorptivity of the medium. The absorptivity of the medium is 0.75 X
Earth absorbs solar energy and radiates infrared energy. The intensity of the solar radiation incident on earth is J = 1350 Wm-2, also known as the solar constant. Assume earth’s surface (ground) temperature to be uniform at Ts, and that the ground and atmosphere are black (emissivity = 1) for infrared radiation. The radius of the earth is 6.378 x 106 m. The diagram shows the ground at the surface temperature Ts and the atmosphere, represented as a thin black layer, at temperature Ta . Suppose the atmosphere absorbs 100% of the infrared radiation emitted by the ground. Assume that the ground absorbs 47.5% of the incident solar energy, and that the atmosphere absorbs 17.5% of the incident solar energy (for a total of 65% absorbed by the planet). Calculate the "steady state” numerical values of the earth’s ground temperature Ts and the atmospheric temperature Ta taking into account the “greenhouse effect” of atmospheric infrared absorption and emission described above.
An engineer is investigating objects that can be used as a solar collector. One ofthe objects considered is the object made of aluminum and is coated with leadsulfate. Investigation shows that the reflectivity of this object is 0.2 for radiationat wavelengths less than 3.3 μm and 0.95 for radiation greater than 3.3 μm. Inorder to get better insight into the behavior of the object, as a candidate for asolar absorber, the object is then exposed to two different conditions: a solarradiation (T ~ 5800 K) and a room temperature (T ~ 300 K). What is the energyreflected by the object at these two conditions?
PROBLEM 4: A black thermocouple is inside a chamber with black walls. If the air around the thermocouple is at 20°C, the walls are at 100-C, and the heat transfer coefficient between the thermocouple and the air is 75 W/m²K, what temperature will the thermocouple read?
Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled on the lower section. The wafer is placed such that the top and bottom surfaces of the wafer exchange radiation with the hot and cold zones respectively of the furnace. The zone temperatures are Tsur,h = 1050 K and Tsur.e = 330 K. The emissivity and thickness of the wafer are e = 0.65 and d = 0.78 mm, respectively. With the ambient gas at T. = 700 K, convection heat transfer coefficients at the upper and lower surfaces of the wafer are 8 and 4 W/m²-K. Find the steady-state temperature of the wafer, in K. Tw i K
Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is reflected from the medium and 130 W/m² is transmitted through the medium, 1) Determine the absorptivity of the medium. 2) Determine the reflectivity of the medium. 3) Determine the transmissivity of the medium.
A composite wall is comprised of two large plates separated by sheets of refractory insulation. In the installation process, the sheets of thickness L = 50 mm and thermal conductivity k = 0.05 W/mK are separated at 1-m intervals by gaps of width w = 10 mm. The hot and cold plates have temperatures and emissivities of T1 = 400 deg C, emissivity1 = 0.85 and T2 = 35 deg C, emissivity2 = 0.5, respectively. Assume that the plates and insulation are diffuse-gray surfaces. %3D Determine the heat loss by radiation through the gap per unit length of the composite wall (normal to the page). Recognizing that the gaps are located on a 1-m spacing, determine what fraction of the total heat loss through the composite wall is due to transfer by radiation through the insulation gap. Hot side Gap w = 10 mm A. 47 W/m, 9.2% T1 = 400°C B. 47 W/m, 10.2% L = 50 mm C. 37 W/m, 10.2% D. 37 W/m, 9.2% T2 = 35°C Cold side 1 m Insulation, k = 0.05 W/m-K
A long, horizontal, cylindrical steel reactor, 1 m in diameter, has a surface temperature of 300ºC. The emissivity of the steel is 0.6, and the heat transfer coefficient for natural convection is 5 W m−2 K−1 . Heat is lost by convection to the air at 15ºC, and also by radiation to the surroundings, which can be considered to be a black body at 15ºC. a) Calculate the total heat loss per metre length of the reactor, and the proportions lost by convection and radiation b) The reactor is then insulated with a thin layer of insulation material to reduce the total heat loss to one-tenth of its original value. This causes the surface temperature of the steel to rise to 400ºC. The thermal conductivity of the insulation is 0.01 W m−1 K−1 , and its surface emissivity is 0.2. Show that the resulting surface temperature of the insulation is about 89ºC, and calculate the thickness of insulation required, stating any assumptions made. Specifically need help with part b
This experiment is conducted to determine the emissivity of a certain material. A long cylindrical rod of diameter D₁ = 0.01 m is coated with this new material and is placed in an evacuated long cylindrical enclosure of diameter D₂ = 0.1 m and emissivity 2 = 0.95, which is cooled externally and maintained at a temperature of 200 K at all times. The rod is heated by passing the electric current through it. When steady operating conditions are reached, it is observed that the rod is dissipating electric power at a rate of 16 W per unit of its length, and its surface temperature is 600 K. Based on these measurements, determine the emissivity of the coating on the rod. The emissivity of the coating on the rod is 0.1165
The tungsten filament of an incandescent light bulb has a temperature of approximately 3000 K. The emissivity of tungsten is approximately 1/3, and you may assume that it is independent of wavelength. To increase the efficiency of an incandescent bulb, would you want to raise or lower the temperature? (Some incandescent bulbs do attain slightly higher efficiency by using a different temperature.)