-25. The beam is used to support a dead load of 5 kN/m, a live load of 20 kN/m, and a concentrated live load of 32 kN. Determine (a) the maximum positive (upward) reaction at A, (b) the maximum positive moment at E, and (c) the maximum positive shear just to the right of the support at C.Assume A and C are rollers and D is a pin. B C D -2m -2 m- -2 m- -2 m- Prob. 6-25

Q: A 2. Find the reactions at Pin A and roller B. The beam is 18 feet long, and the two forces are…

A:

Q: 2-41. Determine the horizontal and vertical components of reaction at the support A, B, and C.…

A:

Q: 9-5. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia…

A:

Q: Determine the Maximum positive moment (kN-m) in the beam shown Where: P = 84kN; w= 10kN/m; L1 = 3m;…

A: Differentiate equation with respect to x acix to obtain bending moment location.

Q: 6-1. Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A, and (c) the…

A: Influence lines  using the Muller Breslau Principle.

Q: Determine the horizontal reaction in kips at the connection A of the gable frame. Assume that A, B,…

A: Consider the figure,

Q: 6-23. The beam is used to support a dead load of 800 N/m, a live load of 4 kN/m, and a concentrated…

A:

Q: at C. Determine the reaction forces of the roller at A, the hinge at B and the fixed support lk / H…

A:

Q: The A-frame shown supports the 250-N load and 85-N load acting on horizontal member. It is hinged at…

A: To find pin reaction at B, C,D

Q: (4) Where should the beam ABC be loaded with a 300-lb/ft uniform distributed live load so it causes…

A: Muller Breslau principle involves drawing the deflected shapes corresponding to the…

Q: 5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000…

A:

Q: 2. Auniform live load of 0.25 k/ft and a single concentrated live force of 3 k are to be placed on…

A:

Q: Determine the reactions at the supports A and B of the compound beam. Assume there is a pin at C.…

A:

Q: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of…

A: Given:- The two forces are applied to the end of the boom OA The magnitude of one force = 200 lb The…

Q: Determine the reaction at support C. Support C is fixed. W= BKN W- BN L-3m. -3m. L-6m

A:

Q: The bearing consists of rollers, symmetricallyconfined within the housing. The bottom one is…

A: Consider the figure,

Q: A uniform live load of 1.8 kN/m and a single concentrated live force of 4 kN are placed on the floor…

A:

Q: A uniform live load of 0.4 k/ft and a single concentrated live force of 6 k are placed on the floor…

A: Solution:  Reaction due to uniform Live load. Influence line diagram for SF @ E From Muller…

Q: Beam AC is attached to the wall and is supported by column BD at the other end, as shown in the…

A: Objective: To determine- A) vertical reaction at A B) load carried by the column at B C) maximum…

Q: FIODICH INO. 2 The frame shown below is subjected to the load of 1.5 kip. For the pins at A and B…

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.