6-15. Draw the influence lines for (a) the vertical reaction at C, (b) the moment at B, and (c) the vertical reaction at D. Assume the supports at A, B, and C are rollers. Solve this problem using the basic method of Sec. 6.1. *6-16. Solve Prob. 6-15 using Müller-Breslau's principle. Α' Probs. 6-13/14 E B F IC 2 m3 m3 m2 m5 m- Probs. 6-15/16 D

6-15. Draw the influence lines for (a) the vertical reaction at C, (b) the moment at B, and (c) the vertical reaction at D. Assume the supports at A, B, and C are rollers. Solve this problem using the basic method of Sec. 6.1. *6-16. Solve Prob. 6-15 using Müller-Breslau's principle. Α' Probs. 6-13/14 E B F IC 2 m3 m3 m2 m5 m- Probs. 6-15/16 D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve and draw the inflence line
Determine the reactions at the pin A and the rollers at B and C on the beam. EI is constant.
2. a. Draw the influence line for member BF of the truss shown. The bottom chord is the loaded chord. b. At what Joint on the truss will a concentrated live load be placed to produce a maximum tensile force in the member BF?
1. Draw the influence line for member FC. Use the tabulation method. 2. A uniform live load of 10kn/m and a single live concentrated force of 35kn are to be placed on the beam. The beam has a weight of 38kn/m. Determine (a) the maximum vertical reaction at support B, and (b) the maximum negative moment at point B. Assume the support at A is a pin and B is a roller.
Sketch the influence line for (a) the vertical reaction at C, (b) the moment at B, and (c) the shear at E. In each case, indicate on a sketch of the beam where a uniform distributed live load should be placed so as to cause a maximum positive value of these functions. Assume the beam is fixed at F.
Draw the influence line for the vertical reactions at A and B. Draw also the influence line for the shear and moment at D.
PLEASE SOLVE THIS PROBLEM USING MULLER Breslau principle.. THANK YOU ( STEP BY STEP SOLUTION )
A roller at A and a hinge at B supports the truss. 2 kN is applied at C. Determine the reactions at A and B. TEUL 3 m B 1m E 1 m 30⁰ 1.5 m 2KN
Q2 Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the shear at C, and the moment at C. D A C B E
Use analytical method and Muller and Breslau principle L1 = 3m L2 = 9m L3 = 3m
The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin) at D. Determine the reactions at the supports. Neglect the thickness of the beam. 1-4. What is the (a) vertical reaction at A, (b) vertical reaction at B, (c) vertical reaction at C, and (d) horizontal reaction at C? 5-6. What is the moment at (a) point A and (b) moment at point D? 7. What is the moment at point A ft left of point C?
Problem 2 The truss shown carries the following uniform live load and concentrated live load. E G 3 m A B C D 3 @ 4 m 12 m LOAD W(LL) P(LL) SET 1 (1,2,3,4,5) 20 90 Draw the necessary influence line diagrams and calculate the following: 8. Maximum axial force on EF. (