25 ap p2 +0.01 20 a. A/m2, and: (a) find the total current crossing ap. 5.5 Let J = the plane z = 0.2 in the a direction for p < 0.4. (b) Calculate (c) at Find the total outward current crossing the closed surface defined by p= 0.01, p= 0.4, z = 0, and z = 0.2. (d) Show that the divergence the- orem is satisified for J and the surface specified.

25 ap p2 +0.01 20 a. A/m2, and: (a) find the total current crossing ap. 5.5 Let J = the plane z = 0.2 in the a direction for p < 0.4. (b) Calculate (c) at Find the total outward current crossing the closed surface defined by p= 0.01, p= 0.4, z = 0, and z = 0.2. (d) Show that the divergence the- orem is satisified for J and the surface specified.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Find the mutual inductance between two coplanar rectangular loops with parallel sides as shown in the following dia- gram. Assume that h₁ >>>h₂.
I need a solution within 15 minutes Q1) By using Laplacian equation, prove that the potential difference of the spherical capacitor does not affect the capacitance value.
3- Write two examples about converting an equation from polar form [contain r.0] to rectangular equation form, [contain x.y] 4- Write two examples about converting an equation from rectangular form [contain x.y] to polar equation form, [contain r,0].
A cubie dielectric slab with constant -4 with sides of length D is inserted a distance r into the space between the plates of a cubic parallel (conducting) plate capacitor with same dimension. Suppose that the capacitor is connected to a battery that maintains a constant potential difference E = 100 V between the plates. If the dielecetrie slab is inserted an additional distance 1 mm into the space between the plates, calculate the change in stored energy. (Take eo = 8.85 x 10-12 F/m.) 132.8 pJ 44.2 pJ 88.5 pJ 221.3 pJ
1) Suppose the capacitor plates have a meaured diameter of (0.210+/-0.001) m and a plate separation of (0.020 +/- 0.001)m. Calculate the capacitance (including uncertainty) of the variable capacitor. 2) The separation (d) for the capacitor in Problem 1 is aried and the capacitance is meauresd for 5 separations. Thes points are recorded in the following table: Note: The Table is in the image. A) Calculate the reciprocal of the separation and prepare a new table that has the separation, reciprocal of the separation and capacitance. Do not calculate uncertainties for the reciprocal separation. B)Plot on graph paper the capacitance vs. the reciprocal separation. C) Determine the slope of this line. D) Use the diameter of the plates from Problem 1 and the slope from part C of the problem to calculate the value of esub0 from this data.
Q4.) A Maxwell's capacitance bridge shown in figure below is used to measure an unknown inductance in comparison with capacitance. The various values at balance: R₂ = 40092, R3- 6000, R4 10002, C4= 0.5 µF. Calculate the values of R₁ and L₁. Also calculate the value of quality factor (Q) factor of coil if frequency is 1000Hz. L1 R₁ R₂ R4
The parallel plate capacitor in the figure below has a plate area A and plate separation d. The capacitor is charged to a voltage Vo, and then isolated. A student then inserts a dielectric slab (dielectric constant K) with thickness t and area A between the plates and parallel to them as shown below (the dielectric does not touch the plates at any time). Once the slab is in place, the student measures the potential difference between the plates. What potential difference will the student measure? You can assume the following numerical values: A=115.0 cm2, d=1.240 cm, Vo=65.00 V, t=0.7800 cm and K=2.610. O24.90 V 39.78 V 65.00 V None of these The answer will depend on the distance of the dielectric from the positive plate, which is not provided in the problem V
The charges of the 2C, C, 2C capacitance capacitors in the figure are qk, qi and qm, respectively. Accordingly, what kind of relationship is there between qk, qi and qm?
Solve this ASAP
Do as soon as possible
You determine the slope of the F vs. V2 graph to be 0.00000000238 C2/Nm2. The length and width of the capacitor plates are 0.127 m and 0.118 m respectively. The plate spacing is 0.65 cm. What is the value of the permittivity of free space in C2/(Nm2)?