Assuming Vtn=1V and Vx and Vy at time 0=0V. ignoring the body effect find Vout at time t=..3V4VVx2VVyVout

Given:A circuit, assuming, To find:Voltage V0 at time t=with ignoring the body effect.

Answered: Assuming Vtn=1V and Vx and Vy at time…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A resistor, an inductor, and a capacitor are connected in parallel to an ac source with voltage amplitude V and angular frequency v. Let the source voltage be given by v = Vcosvt. (a) Show that each of the instantaneous voltages vR, vL, and vC at any instant is equal to v and that i = iR + iL + iC, where i is the current through the source and iR, iL, and iC are the currents through the resistor, inductor, and capacitor, respectively. (b) What are the phases of iR, iL, and iC with respect to v? Use current phasors to represent i, iR, iL, and iC. In a phasor diagram, show the phases of these four currents with respect to v. (c) Use the phasor diagram of part (b) to show that the current amplitude I for the current i through the source is I = √(I2R) + (IC - IL)2 . (d) Show that the result of part (c) can be written as I = V/Z, with 1/Z = √ (1/R2) + [ωC - (1/ωL)]2.
4-) Between parallel plates when two conductive metal plates with an area of 0 cm are separated from each other by 10 mm, a-) Determine the capacitance of the empty condenser run C. b-) Find the maximum amount of load to carry when the capacity r is empty. e-) What is the capacity of the newly formed system and the maximum load the capacity run will carry when mica with a capacity re dielectric constant k 8 is placed? 2/3 Ç-)After loading the capacitance nC, when the external voltage is removed and mica and mm sine nylon (keaytan=3) are placed in 3mm, find the final V and C values. boşluk Sum 2mm
Determine expressions for and sketch is(t) toscale versus time for -0.2 … t … 1.0 s for thecircuit of Figure P4.37 using a differential equation.
The parallel plate capacitor in the figure below has a plate area A and plate separation d. The capacitor is charged to a voltage Vo, and then isolated. A student then inserts a dielectric slab (dielectric constant K) with thickness t and area A between the plates and parallel to them as shown below (the dielectric does not touch the plates at any time). Once the slab is in place, the student measures the potential difference between the plates. What potential difference will the student measure? You can assume the following numerical values: A=115.0 cm2, d=1.240 cm, Vo=65.00 V, t=0.7800 cm and K=2.610. O24.90 V 39.78 V 65.00 V None of these The answer will depend on the distance of the dielectric from the positive plate, which is not provided in the problem V
A solid specimen of dielectric dielectric constant of 4.0, shown in the figure has an internal void of thickness 1mm. The specimen is 1cm thick and is subjected to a voltage of 80 kV(rms). If the void is filled with air and if the breakdown strength of air can be taken as 30 kV(peak)/cm, find the voltage at which an internal discharge
Theoretically obtain the expression of the voltage across the capacitor from the Experiment when the circuit is stimulated with a 5 V direct current voltage source. Assume that initially the capacitor is fully unloaded (null initial conditions). Graph the waveform obtained.
Pls help
Question 7 Consider a bar of p-type silicon that is uniformly doped to a value of N₁ = 2 × 10¹6 cm-³ at T = 300 K. The applied electric field is zero. A light source is incident on the end of the semiconductor as shown in Figure P6.19. The steady-state concentration of excess carriers generated at x = 0 is Sp(0) = 8n(0) = 2 x 1014 cm-3. Assume the following parameters: n = 1200 cm² /V-s, p = 400 cm² /V-S, Tho = 10-6 s, and Tpo = 5 x 10-7 s. Neglecting surface effects, (a) determine the steady-state excess electron and hole concentrations as a function of distance into the semiconductor, and (b) calculate the steady-state electron and hole diffusion current densities as a function of distance into the semiconductor. Light x = 0 p type
An AC power supply is connected to a Capacitor of capacitance 5.5.10-6 F. At time t=0, the power supply is switched on and storts providing a time-dependent voltage VCE) = Vo cos (wt) across the capacitor, where Vo = 5.5 V and w= 373 rad. The Capacitor is initially uncharged. Find the Current, in milliamperes, through the capacitor at € = 2.5s

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Assuming Vtn=1V and Vx and Vy at time 0-OV. Ignoring the body effect find Vout at time t=.. 3V Vx 2V Vy Vout