A charged parallel plate capacitor is filled completely with a dielectric of relative permittivity 9.6. The plate area is 30 cm², the plate separation is 0.2 mm, and the stored charge is 10 nC. Use Gauss' law to find the magnitudes of E, P and D within the dielectric. Find also the potential difference across the plates and the capacitance.

A charged parallel plate capacitor is filled completely with a dielectric of relative permittivity 9.6. The plate area is 30 cm², the plate separation is 0.2 mm, and the stored charge is 10 nC. Use Gauss' law to find the magnitudes of E, P and D within the dielectric. Find also the potential difference across the plates and the capacitance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
Calculate the reactance voltage for a machine which runs at 900rpm number of commutator segments is 65, brush width is 1.74 (in commutator segments), coefficient of self induction is 153 the conductor current is 27A.
2. A single grounding rod electrode is installed in soil. The electrode's resistance to a good known ground is28 ohms. The next ground rod should be installed at least _______ feet away from the first groundingelectrode.A. 15B. 6C. 10D. 25
A Moving to another question will save this response. Quèstion 8 In class A chopper supplying a DC motor, if the back emf of the motor increases then the motor current increases the motor current decreases the load current will remain constant None of the above A Moving to another question will save this response. week10.pptx week9.pptx
Define contactor
TYPE OF APPLIANCES: AIRCONDITION what type of detectors are present in the schematic diagram of the appliance and kinldy discuss the function, and operation of the detector. Kindly include descriptions, schematic diagrams, technical specifications.
Write troubleshooting and maintenance of the three-phase separator ( show your answer in table)
A uniform two-wire DC distributor that is 200 m long is loaded with 2 amperes/meter. Resistance of single wire is 0.3 2/km. Calculate the maximum voltage drop if the distributor is fed from one end. $18.8.8.8.8.8.8.8.8 or 8 (8 tiivaVETEÉ IC IC
How is the grounded dc conductor of a photovoltaic system required to be identified? a. shall be identified at the time of installation by distintive red markings on some of the terminations b. shall be identified at the time of installation by distintive blue marking at all terminations c. shall be identified at the time of installation by a distintive grouping of wires AWG #2 d. shall be identified at the time of installation by distinctive white marking at all terminations.
We are running 3 wires in an IMC to a control panel with a 150 amp circuit breaker disconnect in the control panel. The conduit is run 12 inches above the roof on a strut rack. The ambient air temperature is 88 degrees. This control panel feeds the #1 cooling fan. What sized ungrounded conductors do we need? All conductors have typeTHHN insulation. A #1 AWG B 100 Kcmil C #1/0 AWG D #10 AWG What sized IMC do we need? A 3/4" B 1 1/4" C 1" D 1 1/2"
Discuss in detail different types of induction heating with the help of neat diagram.
Please answer very soon will give rating surely