25° ℗. R IF Block (choice A) Block (choice C) 25° a Ф. Block (choice B) 25 Block (choice D) Φ

Q: Which joining method will be most suited for the assembly of the two components? Provide reasons for…

A: Mechanical joining method will be most suited for the assembly of these  components.

Q: Which one of the following element is used as the energy absorbing element in the machine member.…

A: The term "elastic potential energy" refers to the energy that can be Potential energy stored as a…

Q: Swivel flange center helps to permits the rod buckling due to compression or tensile shock forces.…

A: Answer: True The given statement Swivel flange center helps to permits the rod buckling due to…

Q: Identify the joint types and degree of freedom provided by each joint. Type of Joint and DOF O…

A: Identify the joint types and degree of freedom provided by each joint.

Q: Which lever system has the force in between, like when doing lifting a weight 90 degrees with your…

A: Lever machine: It is a type of simple mechanism in which a rigid arm is fixed about a fixed point…

Q: Columns are subjected to tensile load Select one: O True O False

A: A columns are a vertical structural member intended to transfer a compressive load. that means…

Q: What are the Load factors and what do they include?

A: Load factor: In general, the load factor is defined as the ratio of all the forces (weight of…

Q: Support Reactions will always act parallel to the point of contact of the beam and supports Select…

A: Support of a beam can be fixed or hinge jointed.

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Can someone do a a static force analysis on this? Like method of joints sort of thing. Forgot how…

A: Static force analysis is done to do the analysis of the structure  and to check what will be the…

Q: Do the columns buckle suddenly?

A: Buckling is the deformation or bowing  that occurs in a member subjected to  compressive loads. In…

Q: Why is the 8 kN load not considered here?

A: This question is based on the concept of normal stress.

Q: The first law for an open system is set up. Q12+... AH+AEkin+AEpot- Which term goes in the missing…

A: Work ( W) is going in the missing place in above equation of the first law of thermodynamics for an…

Q: On what is the flexure formula based?

A: The flexure formula is given by: Where, M is the bending moment. I is the moment of inertia. σ is…

Q: 17- What welded joints is the gap gauge used? (ISO 17637) for fillets weld joint a- b- for butt weld…

A:

Q: Truss members can change their length due to a change in temperature. True or false?

A: In truss members, there is no change in length. But due to changes in temperature stress is build up…

Q: Due to imperfections in manufacturing or specific applicationof the load, a column will never…

A: Under the application of axial load over a column when there is a deflection in the lateral…

Q: Evaluate, using language that is technically correct and of a high standard, the results from safely…

A: Given:There are two components that failed: the M24 engine mounting bolt and the fan…

Q: In the figure, L = 3.0 m and P = 590 kN. Compute the member forces listed below. In each case,…

A:

Q: Identify the correct axis of rotation of the joint and the plane of motion of the body or limb…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: What is the Constant Load and Cross-Sectional Area?

A: Load: The load is a force that caused the stresses, deformation, and acceleration in the bodies.…

Q: The relation between joint and frame is N = (2J + 3)  (Where N - number of members,  J - Number of…

A:

Q: Question 5 Answer the following questions concisely (no more than half a page per question): a What…

A: Since you have posted a question with multiple subparts, we will solve first three sub parts for…

Q: Please select all that applies. The possible failure modes for bolted joints are: shear in the bolts…

A: To select: The correct options. Concept used: Failure of the bolted joints: The bolted joints may…

Q: For what purpose is the uniaxial compressive test performed?

A: The uniaxial compression test is performed on a universal testing machine on which a standard…

Q: A set of five SAE Grade 2 bolts are installed to provide a clamping force of 20000 lb between two…

A: Write the given data. Type of bolt=SAE grade 2F=20000 lbn=5σ=0.75σproof

Q: Choose all that apply. Tendency for a column to buckle is dependent on:     Shape of its corss…

A: The deformation caused on the member due to the application of compressive load beyond its critical…

Q: The forces acting on the nut while tightening by a spanner is an example of Select one: Equilibrium…

A: The forces acting on the nut while tightening by a spanner is an example of Moment Moment =Fd

Q: What happens if the load on an actual column exceeds its critical loading?

A: There are two types of the column, 1. Short Column 2. Long Column The slenderness ratio and length…

Q: What causes the localized buckling of the beam's flanges?

A: To find: The causes of localized buckling of the beam's flange Buckling:  It is defined as the…

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: How far does the spring stretch? Include units in your answer

A:

Q: Once the structure has been cut, you must draw a free body diagram of a section. Which of the…

A: The free-body diagram is a diagram that contains all external forces applied on it and also contains…

Q: The transformation from the last joint to the tool contains a rotation of 90 degrees. Select one:…

A: That is true, as we know that the transformation from the last joint to the tool contains a rotation…

Q: Defien the formula used to Determine the flexural rigidity D of the mat ?

A: given; Defien the formula used to Determine the flexural rigidity D of the mat ?

Q: A welded connection is in equilibrium under the action of the four forces shown. Knowing that FA = 8…

A: Given: FA=8 KN FB=16 KN   To find: FC and FD

Q: For instability, at least one joint of the structure should be able to displace without causing…

A: Given: For instability, at least one joint of the structure should be able to displace without…

Q: What is the maximum elastic stress in the column?

A: The moment arm is a combination of both the eccentricity and the maximum deflection in the column.…

Q: In most cases, pre-loading a bolted tensile joint increases the fatigue factor of safety. has no…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.