Can someone do a a static force analysis on this? Like method of joints sort of thing. Forgot how to, please. 10 kN L = 0.4 m 5 kN
Q: Q1 (a) By giving your own illustration examples, explain the differences between: (i) The Method of…
A: Let us discuss about following topics (a) Difference between method of joints and method section (b)…
Q: Young modulus of a material is 250 GPa. What is its rigidity modulus if Poisson’s ratio of the…
A: Young's modulus of a material is, E=250 GPa Poisson’s ratio of the material is, μ=0.3
Q: Describe the Force Method of Analysis for Axially Loaded Members?
A: The force method of analysis is used to solve the statically indeterminate problems like a rod fixed…
Q: Define and describe general buckling. Enumerate and differentiate the different types of general…
A:
Q: et
A:
Q: (7) The cylinder head of a 10"x18" refrigerant compressor is attached by 10 stud bolts made of SAE…
A: Given: Let us consider the given, Cylinder pressure=350 psi Area of the cylinder head,A=10ιι×18ιι…
Q: cause failure of the link by buckling.
A: Given that cross section of BD = 30mm x 30mm Modulus of elasticity of the bar material = E = 200 GPa…
Q: Design knuckle joint joint to resist the load of 100 and 150 kN respectively. The material for both…
A:
Q: QUESTION 3. A simply supportec criangular distributed load as shoe- ielding. Calculate the maximum…
A: givensimply supported beamlength L=2mdepth d=50mmd2=40mmwidth w=10mmtwo triangular load of intensity…
Q: 3-1 Which load class from Table 3-1 best suits these systems? (a) Bicycle frame (d) Diving board (b)…
A:
Q: need 4 & 5 Qi: The load on a bolt consists of an axial pull of 10 kN together with a transverse…
A: Assume - Tensile stress at elastic limit=100MPaPoisson ratio=0.3
Q: enumerate, and discuss different kinds of supports (example: roller support). Draw the corresponding…
A:
Q: What is relationship between the torsional load T= WR and the torsion angle .
A: It is required to write relationship between the torsional load T= WR and the torsion angle
Q: How Fig (1-11)- The thin righld rod is pinned ut polnt A to a negligible mas roller, which rols on a…
A: Degree of freedom is equal to the number of independent variables in the system in order to define…
Q: Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion
A:
Q: Question 5 Answer the following questions concisely (no more than half a page per question): a What…
A: Since you have posted a question with multiple subparts, we will solve first three sub parts for…
Q: Line joining Sut (Ultimate strength of the material) on mean stress axis and Se (endurance limit of…
A: A parabolic curve joining the endurance stress point and the ultimate stress point is called the…
Q: Statics; Method of joints Solve the following problems with accompanying complete- detailed…
A:
Q: 35 - Which of the following statements about supports is false? A) There is no freedom of movement…
A: Degrees of freedom is the no of the independent variable required to define the movement of a…
Q: An aluminium bar is in the form of an equilateral triangle 30 mm on a side. What torque is required…
A: We know that an aluminium bar has 30 mm on each side and is in the shape of an equilateral…
Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…
A:
Q: A machine part has Sut=530 MPa, a fully corrected endurance strength of Se=210 MPa, and f=0.9. The…
A: The greatest load that a material can withstand before showing significant fatigue or severe flaws…
Q: PROVIDE FREE-BODY-DIAGRAM IN EVERY LETTER. Show clear hand writing and complete solution. Thank you…
A: Given: The load, P = 275 kN
Q: 1. Structure analysis of the window opening mechanism of my office in the pic: a.Number of moving…
A:
Q: Name at least three applications or situations where torsional deflection would be undesirable
A: Torsional deflection is the part of deflection under where the shear force is responsible for the…
Q: The following are load diagrams for a bolted tension joint. Which diagram represent a joint that…
A: Answer: c) The sudden slope change represents the failure due to join separation.
Q: What is the inelastic buckling?
A: The strength of a member subjected to compression depends on the material property and its geometry.
Q: Identify at least FIVE (5) factors that affect the Force, F in Figure
A: factors affect the force in above fig these factors leads to improper process and non uniform force…
Q: 1. A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the…
A: Given: The breaking torque is 105 lb-ft. Linear density of the cheater bar is 6.6 lb/ft. The bar is…
Q: For instability, at least one joint of the structure should be able to displace without causing…
A: Given: For instability, at least one joint of the structure should be able to displace without…
Q: two point
A:
Q: What type 0f stress is being experienced by the wires ab0ve?
A:
Q: Plastic stage is when all elements of a steel section is in yielding condition and reaches its…
A: Stages in the loading curve of material are: Limit of proportionality PLastic stage Ultimate…
Q: C) Discuss the main factors influencing on Buckling behavior
A: A moment of inertness quantitative measure of a body's rotational inertia is the body's resistance…
Q: 04: Torque wrench in the fig. is made of 350MPA steel and loaded with 1 kN load. Find out the most…
A: To given that,Torque wrench in fig.=350MPaLoad=1KN so first of all we will find, Bending…
Q: Which material is NOT capable of holding a static load at 600 °C? Magnesium Nickel Aluminium…
A:
Q: What are the mechanics of torque tube failure and the failure pattern?
A: It is asked to explain about the failure mechanism in torque tube
Q: Rolling contact Pin in slot
A: Given:- To Find :- Degree of freedom (DOF)
Q: Which is procedure provides a method that may be used to determine the displacement of any joint on…
A: We can use the method of virtual work to determine the displacement of a truss joint when the truss…
Q: Complete( any five) of the following: 1- In fatique, the load ratio equals to 2-The relationship…
A: Given questions: 1. In fatigue, the load ratio equals to 2. The relationship between residual…
Q: for the lap joint shown below, calculate the safe axial tensile fo 126 102 A 220M
A:
Q: A steel specimen with square cross section is going to subject to impact test. Describe hov to…
A: To describe how to measure the impact energy from the test.
Q: The relation between joint and frame is J = (2N - 3) (Where N - number of members, J - Number of…
A: true
Q: When in tune, a steel banjo string has a tension of 1300 N. If the ultimate tensile strength of the…
A: Given:Tensile force in string,T=1300NUlimate tensile strength,σ=600MPa=600×106Pa=600×106Nm2Factor of…
Q: Which set of compatibility equations matches the following torsion members connected end-to-end in…
A: Given Torsion members To find Compatibility equation Compatibility equation are the equation which…
Q: cal load limit equation (Pcr) - buckling on a machine structure? c)How to improve the ability of a…
A:
Q: A: Draw the Free Body Diagram only of next fig.
A:
Q: the critical design load
A: In order to find critical design load we have to equate with reactive force per unit area:so…
Q: What does the application of the flexure formula require?
A: given: What does the application of the flexure formula require?
Step by step
Solved in 3 steps with 1 images
- Original length of rod is 1000 mmSTATICS : METHOD OF SECTIONS - GET THE GIVEN, WHAT IS ASKED, AND THE ANSWER. - MAKE A PROPER FREE BODY DIAGRAM. (IT DOES HAVE THE GREATER POINTS IN THIS ACTIVITY) - YOUR SUB ANSWERS MUST BE IN 6 DECIMAL PLACES. - YOUR FINAL ANSWER MUST BE IN 4 DECIMAL PLACES. - TELL THE DIRECTION AND WHETHER IT IS TENSILE OR COMPRESSION. - WRITE YOUR SOLUTION PROPERLY (EASY TO UNDERSTAND). - I PROVIDED A SAMPLE PROBLEM SO THAT YOU WILL KNOW HOW TO SOLVE IT. THANK YOU IN ADVANCE! Solve the forces in PQ, FL, QG, and QM. Hint: Identify all zero-force members and remove them from the structure. In the summation of moments, look for a point where member forces at the supports converge so that their moment arm is zero. From here you will be able to solve PQ. Solve FL using summation of moments from the other half of the section. Solve QG and QM using Method of Joints.PLease answer this correctly ASAP. Note:Tolereance is ± 1 in the 3rd significant digit. Exact answer please. This is a step by step question and I font have enough time to answer this so please can you answer all the necessary information/joints/points? I will rate you based on your answer. Thank you so much