Line joining Sut (Ultimate strength of the material) on mean stress axis and Se (endurance limit of the component) on stress amplitude axis is called as

Q: he values of stress amplitude and stress ratio

A: Given ; From the given figure; Fluctuating fatigue load Find the stress amplitude and stress ratio ?…

Q: Suppose an ideally-prepared test specimen in an R.R. Moore rotating beam test has an ultimate…

A:

Q: The similarity between statics of rigid bodies and strength of materials. (A) Both dealing with…

A: Statics of rigid bodies deals with the equilibrium condition at static position.   Strength of…

Q: pls find box ur answer Determine the value of the von Mises stress at point A. The von Mises stress…

A: The values are P=4 kN, F=0.55 kN, T=25 Nm The yield stress is Sy=280 MPa The length of the pipe is…

Q: A non-rotating 1.50-inch diameter solid steel rod with its surface machined under a fully reversed…

A:

Q: ngineering of materials need hel

A:

Q: Strength sensitivity for strain rate increases with temperature: Select one: True False

A:

Q: the load, what happorns Afler releasing the longth and width ok the wire

A: we have to calculate stress strain elongation , lateral strain.

Q: Q4/a- Astructural component of an engineering design loaded in plane strain cnodition must support…

A: Solution:To solve the problem of calculating the length of the largest internal flaw that the…

Q: A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for…

A: Answer: (a) The stress ratio, the stress amplitude and the mean stress: R = -1 σa = 213 MPa σm = 0…

Q: Problem 2: Use an eigenvalue approach to solve for the principal stresses and directions for the…

A:

Q: A belt driven pulley, transmitting torque , weighs 1.8 kN. It is mounted between two bearings 3 m…

A:

Q: QUESTION 1 A Z-section beam of 2 m long and is supported as a cantilever with a 1 kN load at the…

A:

Q: the Mohr's circle

A: Given; The stress at a point in a material under plane stress conditionis uqui-biaxial tension with…

Q: In the engineering stress-strain curve for mild steel, the Ultimate Tensile Strength (UTS) refers to…

A: Meanings of all four options are explained below:   Yield stress : It is the stress upto which…

Q: 3. Find the equivalent stiffness as shown below. Draw the free body diagram. x10 Nm sx10' N 45 10 Nm

A:

Q: Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the…

A:

Q: Compute Sn and sketch the goodman fail the part drawn below. Material is cold rolled steel.

A: GivenSu=520MPaSy=350MParelaibility =90%colled rolled steel

Q: An Aluminum shaft is compressed by a load of 28000 Ib. The original length is 2.8 in and the…

A: Given Case 1 Diameter = 1.3 in Length = 2.8 in Force = 28000 lb Modulus of elasticity = 85000 =…

Q: 8. Refer to the figure below. Even though the cyclic loading accidentally caused the stresses to…

A:

Q: OD In Figure show the fatigue curve for a metal. a) If a sample was taken from this material with…

A:

Q: Q: 1 Define the following and give the formula if exists? 1. Poisson's ratio 2. Brittleness 3.…

A: Let's us one by one define each of the following topics

Q: MPa 70 60 50 40 30 20 10 10-3 80 E 20 40 60

A:

Q: a) A long cylindrical bar is loaded by an axial tensile force F. What is the change in length AL and…

A: (As per Bartleby's authoring guidelines, only one question at a time to be answered.)a)Change in…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.