22: The springs connecting with a rigid weightless bar as hown. The stiffness of beam (Kb) is 5 kN/m and the tiffness of all the springs (K) are 4 kN/m. Find the natural requency for the system. Im n K 2m 3m K

22: The springs connecting with a rigid weightless bar as hown. The stiffness of beam (Kb) is 5 kN/m and the tiffness of all the springs (K) are 4 kN/m. Find the natural requency for the system. Im n K 2m 3m K

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem: Determine the maximum shearing stress developed in each material. Also, determine the…

Q: Design a compound shaft attached to rigid support using bronze with G=35 GPa and allowable shear…

A: Assumptions in the theory of torsion: The circular shaft material is uniform throughout the…

Q: (a) the normal stresses in the bronze and steel rods o1,02 (positive if tensile, negative if…

Q: 1. Find the support reactions for the steel bar, after it is loaded, as shown below (E = 200 GPa). A…

A: Given : E = 200 GPa Find the support reactions for the steel bar ?

Q: For the below wooden beam, under the given loading and dimensions: 50 kN 4m Calculate the reactions…

A: Given: Ewood=12 GPa To find: Reaction at the support

Q: Q1: A torque T=4 kN.m G of steel core 77 GPa and G of aluminum 27 GPa. Determine: (a) maximum…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: Given data in question Load 88 kN Area 520 and 280 mm2 Elasticity modulus 110 and 67 GPa To find…

Q: The A-36 steel rod has a diameter of 50 mm and is firmly attached to the rigid supports at A and B…

A: Given data, d = 50mm T1 = 50 degrees °C T2 = 30 degrees °C For A-36 steel a=12x10^-6/°C E = 200GPa…

Q: A. Determine the determinacy and stability of the following structure. Hinge Hinge (a) (b) Hinge (m)…

A: Given data in question Various structures To find out Static indeterminacy and stability. Note:…

Q: Determine the stretch in springs AC and AB for equilibrium of the 2-kg block. The springs are shown…

A: Given:- Mass of the block = 2 kg Stiffness in spring on AC = kAC = 20 N/m Stiffness in spring on AB=…

Q: Part C The hand truck and its contents have the center of gravity at G. Assume that there is no…

A: As there is no contact between wheel and horizontal surface, there wouldn't be vertical reaction but…

Q: The rigid beam is supported by three rods, each having a cross- sectional area of 850 mm². Rods AB…

A: Area of rod (A) = 850 mm2For 2014-T6 Aluminium,α =25×10-6 /°CE = 69 GPaFor 304 stainless steel,α =…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: The staves or vertical members of the wooden tank are held together using hoops having a thickness…

Q: *5-4 The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Maximum shear stress is 26.73 MpaExplanation:Step 1: Step 2:

Q: The rigid block has a weight of 400 kN and is to be supported by posts A and B, which are made of…

A: Given, Weight of the block = 400 KN The length of each block is the same Cross sectional area =5000…

Q: The wire AB is unstrentched when tetha = 45 degrees. If a load is applied to the bar AC, which…

Q: Determine the reactions at the supports of the beam which is loaded as shown.

Q: A bracket connected to the flangé of a column through a group of rivets to transfer a load of 120 kN…

Q: f P8-4. Determine the force P needed to cause impending motion of the block. 2m W = 200 N 1 m…

Q: A solid circular bronze [G- 6,500 ksi] shaft, 5.4 ft long and 1.125 in. in diameter, carries a…

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When…

A: The temperature variation in the pipe is as shown below. The expression for the temperature…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: Given data in question Load 88 kN Area 520 and 280 mm2 Elasticity modulus 110 and 67 GPa To find…

Q: F1 (kN) 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: The frame system shown below consists of two, 3-m radius, frictionless pulleys at points B and D.…

A: Given -

Q: Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt…

A: We have to find out the unit stress in each bolt with the given data,

Q: A hoop is shrunk on to a tube exerts a contact pressure of 3000 psi on the tube.an internal pressure…

A: Solution;

Q: The pin-connected rigid rods AB and BC are inclined at 0 the force P is applied, 0 becomes 32°.…

Q: Calculate the total elongation of the spring system shown if W = 2000 N, P = 4000 N, k1 = 200 N/mm,…

Q: Problem 2 The mechanical system consists of two identical steel rods (A = 30 mm2, E = 200GPA, a =…

A: To determine the axial stresses in rods 1 and 2 and the angle through which the beam AC would…

Q: The truss shown in figure below is supported by a hinge atA and a roller at B. A load of 2000 kN is…

A: To find support reaction at support A and B

Q: The cylinder and the block are connected by a horizontal cord. Determine the largest couple C that…

A: Free Body Diagram To find:- Couple (C)

Q: HW (4-1): If the area of each bar of the truss shown in 2w figure is (2700 mm') and the movement of…

A: Calculate the moment about A as; ∑MA=01×10-RD×cos4.5°×10+RD×sin45°×30=0RD=-0.707 kN Calculate the…

Q: c) Calculate the vertical reaction at support B. When sketching FBD, assume the positive direction…

Q: Problem 2 (for all students). Determine the state of stress, the principal stress and the max in-…

A: Calculating the moment of inertia: IP=π32504-404 The torque will be:T=6×300=1800 KN-mmThe bending…

Q: cmonl *9-56. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and…

Q: A hollow steel tube (1) with an outside diameter of D1 and a wall thickness of t1 is connected to a…

A: E1 = 210 GPaE2 = E3 = 55 GPa Determinea. The movement of joint B with respect to support A. b. The…

Q: Determine the magnitude of the pin force at A. Assume W = 765 lb, a = 3.8 ft, b = 2.9 ft, r = 9 in.…

Q: Ex/Determine the reaction 4m TWIT wh B 2m 2 KN 2m MITA wh C

A: ##Determination of Reactions using force method of Analysis ####

Q: The load P produces an axial strain of -1,800 pe in post (2). Determine the axial strain in rod (1).

A: Given Diagram with dimensions Strain in post 2 = 1800 To find Axial strain in rod 1

Q: The springs BA and BC each have a stiffness of500 N/m and an unstretched length of 3 m. Determinethe…

A: Given :- k= 500N/m L=6m F=175 N To find:- d

Q: 2-29 The nonuniform loading causes a normal strain in the shaft that can be expressed as e, = kr²,…

Q: Determine the vertical displaent of joint B. The members are pin conneced at their end points AA:…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

22: The springs connecting with a rigid weightless bar as
hown. The stiffness of beam (Kb) is 5 kN/m and the
tiffness of all the springs (K) are 4 kN/m. Find the natural
requency for the system.
K
Imm
444
3m
K

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Trending now

This is a popular solution!

Step by step

Solved in 9 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in, by 4 in. in section. Identify all the reactions (reaction at A and C). Compute the maximum tensile stress developed in bar CB assuming the pin connections at A, B and C are frictionless. Please include the details, thank you.
O Determine the support reactions o- 10 beam shown here: 9=300 lb/ft Solution: 1- Support 2- FBD: 3- unknowns : AT y" 4' the F=400 lb. So=60° Brom 5
В A B C The system above is comprised of two-force members AB and AC, supporting a vertical force at point A. Assuming the system is drawn to scale and is in equilibrium, which of the following best describes the nature of the forces in members AB and AC? a) AB is in tension AC is in compression b) AB is in compression AC is in compression c) AB is in tension AC is in tension d) AB is in compression AC is in tension
The machine shown is used for forming metal plates. It consists of two toggles ABC andDEF which are attached to a hydraulic jack at pt. H. The toggles push the curved bar at Gforward, pressing the plate into the cavity. The curved bar at G slides along frictionless rails atthe top and bottom of the machine. If a 12-kN force is applied to the center of the plate,determine the force, F, from the hydraulic jack in the configuration shown.
The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
135 mm 85 mm σ, = -58 MPa E = 105 GPa D = 0.33 Beer & Johnston & DeWolf & Mazurek 2.86 (a) For the axial loading shown, determine the change in height and the change in volume of the brass cylinder shown. (b) Solve part a, assuming that the loading is hydrostatic with Ox= Oy = O₂ = -70 MPa
The 300 N homogeneous bar AB, as shown, is supported by a pin at A and the cord BC. Determine the pin reaction at A on the bar AB. A -4 m 3 4 B 7
P8-1. Determine the friction force at the surface of contact. 500 N 3 W = 200 N plus 0.3 Mk = 0.2 100 N (a) (b) Prob. P8-1 W = 40 N μ = 0.9 Mk = 0.6 P P
Aload Pissupported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17400 ksi] rods, and a solid steel [E = 30600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.79 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.52 in. Assume L1=39 in and L2=77 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. |(2) (1) L2 (1) B. Answers: i ksi. ksi.
From the frame loaded as shown. Solve the following Find: Reaction at column BMoment at column B
The rod and the tube are of the same initial length and must remain together then the strain in each part must be the same. A compound bar is made up of a rod of an area A1 and modulus of elasticity E1, and a tube of equal length of A2 and modulus of elasticity E2. If a compressive load P is applied to the compound bar, find how the load is shared. The total load carried is P and let if be shared W1 and W2
The A-36 steel rod has a diameter of 50 mm and is firmly attached to the rigid supports at A and B when the initial temperature is 50°C. Determine the force P in kN that must be applied to the collar at its midpoint so that, when the final temperature becomes 30°C, the reaction at B is zero. Where: α=12x10^6 m/(m°C), E = 200 GPa and L = 500 mm