21 The root of a thread is defined as what? Multiple Choice (select the best answer) The surface of the thread along the minor diameter. The surface of the thread along the major diameter. O The distance a screw travels axially with one rotation. O The measurement between the crest and root of a single thread. 22 The thread depth of a thread is defined as what? Multiple Choice (select the best answer) O The measurement between the crest and root of a single thread. O The number of threads which span one inch of an inch series thread. O The surface of the thread along the minor diameter. O None of the Above What operation finishes a hole to a precise size with a Multiple Cholce (select the best answer) 23 O Drilling Tapping Reaming None of the Above

21 The root of a thread is defined as what? Multiple Choice (select the best answer) The surface of the thread along the minor diameter. The surface of the thread along the major diameter. O The distance a screw travels axially with one rotation. O The measurement between the crest and root of a single thread. 22 The thread depth of a thread is defined as what? Multiple Choice (select the best answer) O The measurement between the crest and root of a single thread. O The number of threads which span one inch of an inch series thread. O The surface of the thread along the minor diameter. O None of the Above What operation finishes a hole to a precise size with a Multiple Cholce (select the best answer) 23 O Drilling Tapping Reaming None of the Above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: 4X .250-20 UNC-2B 1.260±.010 .984±.010 2.600 ø2.012 2.008 Ø 3.350

A: the position tolerance for the diameter hole 2.012/2.008 and the diameter stud 2.006/2.002 position…

Q: I need answers to parts 10, 11, and 12, pertaining to the print provided.

A: Hii,thanks for the question but there is only 10th question so we are answeering only 10th…

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

Q: Solidworks 24 threads per inch Units: IPS Mass = 0.0681 pounds Volume = 0.2417 cubic inches…

A: It is asked to create a bolt as shown in the question Make sure the unit system is IPS selected from…

Q: I have three parts that need to be answered pertaining to the print provided below. What size…

A: The size of the print provided in the title box is C.Hence the correct answer is C.

Q: Compare the bolt patterns in shear shown below. The distance from the load to the centroid is the…

A: following is the answer and explanation for the above question-

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: How long is the thread at 4B? What do the brackets around dimension 241 at 3C indicate?

A: It is asked to find the length of thread in section 4B and also the meaning of parenthesis in…

Q: a) The maximum force P that can be applied to the system based solely on the boards is most nearly…

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given - L = 25 ft = 25 × 12 P = 10000 lb ∆L = 0.477 in E = 30 × 106 psi

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: 14 inch is the correct answer.

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Complete the needed calculations and enter the needed values in the given table. All problems are…

Q: Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in.. 7.80…

A: The standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in. are: 7.80 in. 7.95 in.…

Q: Connecting rod bearings are to be replaced. The journal measures 70.866 mm (2.790 in.). The…

A: The Size bearings for above requirements are U/S--0.381 mm (0.015 in) undersize.

Q: Dimensions are the linear or angular sizes of a component specified on the part drawing: Group of…

A: Introduction: Engineering drawings are a subset of technical drawings. The goal is to provide all of…

Q: The feature of saw blade geometry that allows the blade to cut a kerf that is wider than the blade…

A: A feature is responsible when a blade cut a kerf which is wider than the blade itself.

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A: The old tyre is P 160/70 R14 ie. 160 shows the section width in mm 70 shows aspect ratio R14 rim…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

Q: Explain the major diameter of a thread.

A: A thread can be defined as the ridge which is wrapped around the cylinder. The wrapping can be in…

Concept explainers

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.

Question

21
The root of a thread is defined as what?
Multiple Choice (select the best answer)
The surface of the thread along the minor diameter.
The surface of the thread along the major diameter.
O The distance a screw travels axially with one rotation.
O The measurement between the crest and root of a single thread.
22
The thread depth of a thread is defined as what?
Multiple Choice (select the best answer)
O The measurement between the crest and root of a single thread.
O The number of threads which span one inch of an inch series thread.
O The surface of the thread along the minor diameter.
O None of the Above
What operation finishes a hole to a precise size with a
Multiple Cholce (select the best answer)
23
O Drilling
Tapping
Reaming
None of the Above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given as 0.985"/0.980 37. What is the maximum clearance for this fit? 0.030" 0.020" 0.025" c) 0.010" (P 38. What type of fit is this? transition b. clearance interference d. none of the above 39. A fit can be determined by specifying: upper limit b. allowance max. clearance b& c all the above TE d. 40. A fit is specified as 60H1109 in Metric unit. What is the tolerance grade for the shaft? 60 a. b. 9 11 d. none above
Need questions 13, 14, 15 explained and answered please.
What tolerance is specified for the width of the groove?
I need help with this assignment for drafting I don’t understand it.
The strains can be eliminated by using the generalized form of Hooke’slaw.True or false?
Correct answer writing
What is the MMC of shaft "C"?
Can I get the Top, Side and views. Using free-hand drawing of this coupling pieces..
Hello, please answer as soon as possible. Choose from the given choices/options below the question. Show complete solution. Thank you for your help. I’ll rate you with like/upvote.
The diameter of a 3/4-10 American Standard thread is to be checked by the three-wire method. What is the largest size wire that can be used?
Draw the shear diagram for the beam. Click on "add vertical line off" to add discontinuity lines. Then click on "add segment" button to add functions between the lines. Note 1 - Make sure you place only one vertical line at places that require a vertical line. If you inadvertently place two vertical lines at the same place, it will appear correct visually because the lines overlap, but the system will mark it wrong. Note 2 - Indicate the segments for all values of x shown in the diagram. Even if a segment is a constant value 0, it should be drawn in the diagram. +0 No elements selected M V, lb 600- 500 400- 300- 200 100 0. -100 -200 -300- -400 -500- -600 50 lb/ft 20 ft 10 B 8 200 lb-ft 10 ft 30 x, ft ? Press TAB to navigate between elements on the canvas. Press ALT+M to get to the main menu. Press ALT+A to modify the attributes. Press (ALT+Q) to quit the application.