200 mm 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a 20-mm-diameter pin at D that is in double shear. Determine (a) the required diameter of the connecting rod AB, given that its tensile working stress is 100 MPa; and (b) the shear stress in the pin. -240 mm- 50 mm 10° -150 mm- FIG. P1.37 FIG. P1.36 30 KN 50 mm

200 mm 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a 20-mm-diameter pin at D that is in double shear. Determine (a) the required diameter of the connecting rod AB, given that its tensile working stress is 100 MPa; and (b) the shear stress in the pin. -240 mm- 50 mm 10° -150 mm- FIG. P1.37 FIG. P1.36 30 KN 50 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Do in 3 min
2. The assembly shown below is subjected to the load P applied at 30°. The cylindrical pins at A, B, C, D, and E are identical and made of the same material whose allowable shear stress Tallow = 40.0 MPa and has a diameter of d = 3.0 mm. Determine the maximum load P that can be applied. 1 m 1 m P C 30 B. 45° 3 m
Four plates, each being 15 mm thick, are to be connected by six bolts of 19 mm diameter as shown. Consider B = 181 mm. Assume that the force is equally distributed among the rivets. A. Determine the minimum force P (Newtons) if the allowable bolt shearing stress is 33 MPa. B. Determine the minimum force P (Newtons) if the allowable plate bearing stress is 32 MPa. C. Determine the tensile stress of the top plate (MPa) at segment a-a if the force P is 35 kN.
Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel and aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist more than 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa, Ga 28 Gpa. Aluminium Steel 75 .mm 100 mm 1m
مقاومه HW2
1. a) Fig. Q1(a) shows a system consisting of two links; AC and BD. Link BD has a width of 40 mm and thickness 15 mm. Each pin has a diameter of 12 mm. Compute with the aid of free body diagram, the maximum average stress in link BD when = 10⁰. 300 mm 30° B Fig. Q1(a) 150 mm D 20 kN to
Q7 For the bracket shown in the figure: > The moment of the force (1000N) about pin A is...... > The moment of the force (1000N) about pin B is...... The moment of the force (1000N) about pin C is. 600mm 1000 N 500mm 200mm 240 N.m CCW, 562 N.m CCW, 1099 N.m CCW 200 N.m CW, 468 N.m CW, 915 N.m CW 562 N.m CW, 1099 N.m CW, 240 N.m CW 468 N.m CW, 915 N.m CW, 200 N.m CW O GOOD LUCK! Eiminer Asst. Lecturer. Reem Al-Timimi Head of the Department Dr. Hussein Sadig
7.5 B(1) Refer to Figure 7.13, which shows a flexible rectangular area. Given: B₁ 1.22 m, B₂ 1.83 m, L₁ = 2.44 m, and L₂= 3.05 m. If the area is subjected to a uniform load of 144 kN/m², determine the stress increase at a depth of 3.05 m located immediately below point O. B(2) 2 = (1)- 3 4 L(2)- Figure 7.13 Stress below any point of a loaded flexible rectangular area
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
Example 3.8. A lever is keyed to a shaft of 100 mm diameter. The width of the key is 12 mm and the length is 50 mm. Find the load that can be applied at a radius of 1.2 m, if the shear stress in the key is not to exceed 100 N/mm². AB 12mm 100mm
Discuss the dependency of the thermal efficiency of the ideal Otto cycle on compression ratio and engine knock.
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.