2. Two rollers of the same diameter shown in the figure are supported by an inclined plane and a vertical wall. If all surfaces are smooth, find the reactions induced at points A, B, and C. ( 120N 80N B 30

Q: F. 5N 5N 5N 10cm M. 7.5N 6.1cm 5.15cm 7.5N

A:

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: 3 50mm link is fixed, the number of finks can rotate fuy filly that

A: Given data: Let 4 links;s=100 mmp=200mmq=300mml=350mmas shown in fig. if 350 mm is fixed  then  no.…

Q: Write about characteristics of gyroscope with a neat sketch.

A: The answer is in next steps

Q: Distinguish nominal diameter and gross diameter of bolt

A: Nominal diameter:Nominal diamater can be described as the pitch diameter of the thread of the…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Power is transmitted from the 1st shaft to the 2nd shaft with a Conical Friction coupling at 950…

A: Given: The speed of coupling, N = 950 rpm The taper angle, α = 25° The mean diameter, D = 120 mm

Q: A cast-iron gear with 100-mm effective diameter and t = 40-mm hub engagemen length is to transmit a…

A: Given: R - 10 mm t - 40 mm T - 120 N.m ro - 50 mm Ec - 100 Gpa Es - 200 Gpa f - 0.16  v - 0.3 To…

Q: clearance in the assembly

A: Given; In an interchangeable assembly, shafts of size = 25.00-0.0100-0.040mmsizes of  holes=…

Q: 3. Design Challenge: The wind turbine is designed to generate 2.5 MW of power with the blades…

A: Given: To find: design the shaft

Q: 6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center…

A: Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Q: 7) Given the ISO metric hexagon socket screws in the figure; select the correct name of the head…

A: For question number 7 the correct answer is option b. As the first figure is of cap screw and second…

Q: Provide information about tempering heat treatment temperature stages, microstructures formed and…

A: Tempering is a heat treatment process, which is mostly used to increase the ductility, toughness and…

Q: What is a double-rod cylinder? When would it normally be used?

A: Two types of cylinders are: Single rod cylinder Double rod cylinder.

Q: How pilot tube works?

A: The pitot tube is a simple device that is used to measure the flow velocity with no moving parts.

Q: If the pitch of a thread is 1/18 inch, how many threads are needed for the threaded section of a…

A:

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: It is desired to punch a 1.5-in dia. hole through a 1/8-in metal plate which has an allowable stress…

A:

Q: The . . nut is a hexagonal nut with ......e ... washer. dome flanged . cap square The of an object…

A: Let's discuss the types of nuts:- Dome nut means the dome head at the top of the nut. That's why it…

Q: Thread Fits and 7. Define fit, allowance, tolerance, and limits. Classifications

A: Topic : engineering drawing

Q: 6/20 The force P is applied to (a) the 60-lb block and (b) the 100-lb block. For each case,…

A:

Q: What is the Flexure Formula?

A: The stresses in the beam caused by the bending moment is called as flexural or bending stress.

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: Use the Griffith analysis to calculate the critical stress required for the propagation of an edge…

A: We may determine the critical stress required for the propagation of a surface crack in soda-lime…

Q: Provide any six types of flanges used in piping.

A: Here are six common types of flanges used in piping systems:Weld Neck Flange: Characterized by a…

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: List some factors of safety for design of drilled shafts.

A: A drilled shaft is a deep foundation that is constructed by placing fluid concrete in a drilled…

Q: lestion IJ alculate the maximum stress in 0.10-i 2.00-in dia. Applied torque %3D

A:

Q: What will be the length of given mild steel rod after applying 100 kips force/load ?. If the…

A: Given, Force applied = P = 100 kips = 100 x 103 lb Diameter of rod = d = 0.5 in Length of rod = L =…

Q: Explain the differences between single and multiple threads. [ Draw and describe the function and…

A: Introduction: Threads are spiral grooves of identical size or shape created on a circular…

Q: 2. A machine shaft turning at 600 rpm is supported on bearings 20" apart. Twenty HP is supplied to…

A: Given: The shaft speed, N = 600 rpm The distance between bearing, x = 20 in The diameter of pulley,…

Q: required punch diameter ?

A: Given data;   A meatal disc is to be punched having following data,i.e,  Diameter,d=30 mm…

Q: 1- Draw three views of hexagonal nut for 24 mm diameter bolt according to rough rule dimension.

A: We can answer first question since the exact one is not specified. Please resubmit the question by…

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: The guide for the width of the key is O 1/4 of shaft diameter O 1/3 of shaft diameter 3/4 of shaft…

A:

Q: 5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define…

A:

Q: Write the equation for work done by a torque of constant magnitude?

A: Work done: The work done is defined as the product of force and the displacement in the direction of…