Write about characteristics of gyroscope with a neat sketch.

Q: A chain drive is required to transmit a design power of 4.13 kW from a motor to an output shaft. The…

A:

Q: Problem 1 Given: Mass of canister: 4000 kg Mass of beam BD: 50 kg Max allowable force: 1. AB = 30 kN…

A:

Q: Determine the moment of inertia about the neutral axis. 50 mm 50 mm 50 mm A B 50 mm 50 mm 50 mm

A:

Q: What is gyroscopic effect?

A: Angular velocity is defined as the change in the angular position of a body following circular…

Q: Please create a simple ping pong ball launcher where there is a mechanism for the trigger. And…

A: We have to given a initial launch angle and a launch initial velocity. And according to the initial…

Q: A car is moving on a curved horizontal road of radius 100 m with a speed of 20 m/s. The rotating…

A: Given:ω=100 rad/s I=10 kg-m2r=100 mv=20 m/s

Q: 17-A28 The 2000-kg truck has rear wheel drive. The coefficient of friction between the rear tires…

A:

Q: 3. Consider the shaded area shown. a) Determine the y-coordinate of the centroid of the shaded area,…

A:

Q: For items 4-5, consider the following: At the instant shown, drum D rotates at a constant angular…

A: Given: The angular velocity of drum, ω = 10 rad/s (CCW) The angular velocity of rod AB, ωAB = 5…

Q: A vehicle is traveling on a curved road at a speed of 55 ft/s at point A, as shown in the figure…

A:

Q: 02: Fully describe the gyroscopic effects on ships.

A: The front side of the ship is known as a bow and the rear end (the end where the rotor is present)…

Q: The platform scale consists of a combination of third- and first-class levers so that the load on…

A: Given DataThe mass of the counter weight is: The acceleration due to gravity is: To DetermineThe…

Q: The kinetic energy needed to punch a hole is 7KJ. What is the maximum thickness of hole diameter is…

A: Given: K.E  = 7 KJ d= 45 mm τs = 480 Mpa

Q: How can we determine the displacement with truss?

A: Virtual work method: This method is a very important method which s used to find the slope as well…

Q: Read through the following chronological instructions. Choose the correct figure that best matches…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: Describe two types of benders for soft tubing.

A: A metal pipe bender is an important machine tool that provide pipe bends for a vast number of…

Q: angular speed of Gear 5 is

A: Given data, Gear 2 rotates at 1200 rpm N2= 1200 rpmIt is engages with gear 3 and gear 4 mounted on…

Q: We used the average sea level pressure Po What is the mass of air pressing down on the top of your…

A:

Q: The beam supports two loads, w;(x) = 20x² + 100, where w, is in lb/ft and x is in ft, and a linearly…

A: Given Data: The load w1=20x2+100 and a span of 0'<x3' The linearly varying load is from 280 lb…

Q: Determine the moment of the force about point O. - 4 ft- 3ft 45 -1 ft- 600 Ib

A: The perpendicular distance from point O to 600 lb  =4ft+3ftcos45°-1ft=5.1213ft

Q: A tripod plotted in a 3-D coordinate system is supporting a downward vertical load of P = 443 kN at…

A:

Q: 2. Calculate the volume of hexagonal head bolt by measured data at Instruction 1.

A: GivenPart A(tail part).Volume=π4c2DVolume=π4×15.582×40.11Volume=7642.8mm3Part B(Head…

Q: Apply the formulas in designing a hydraulic turbine to select the appropriate type of turbine for…

A:

Q: 8-7. A boiler is constructed of 8-mm thick steel plates that are fastened together at their ends…

A:

Q: v = 4 m/s A P 30° 0.5 m the 5-kg collar A is sliding around a smooth vertical guide rod. At the…

A:

Q: Rotary crusher work better on materials Brittle and hard Soft and plastic O The two types O

A: Rotary crusher are generally used to crush brittle and hard materials. They are used in mines.

Q: va three DoF (Degree of freedom) eight link (n=8) mechanism with rev rify DoF mechanism using…

A:

Q: 7. The head lost in each pipe in the figure is given by HL = kQ?, where Q isth m/s and HL is in…

A: Disclaimer : “Since you have posted a question with multiple sub-parts, we will solve first three…

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.