Answered: convert 15 rpm to spm

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter49: Wheel Alignment

Section: Chapter Questions

Problem 1RQ: Define camber.

See similar textbooks

Similar questions

Determine the horsepower of a 6 cylinder 4 stroke continental engine having a bore equal to 3.875 in stroke of 4 in, and rpm of 2700 if it has a bmep of 150 lb/sq. in.
4. Convert 12,800 rpm into (rad). (1 rev = 360⁰ = 2 radians)
A bucket elevator has a head pulley diameter of 14 inches. There are 260 buckets having a size of 4 in wide and 6 in long attached to its belt at 1 ft spacing. What will be its recommended rpm and the speed in number of buckets per minute?
what is the speed ratio of v/U for part b?
B1
Q: Two involute goars having module 3 mm and pressure angle 20 meah esternally to give a velocity ratio of 3 For this mechaniam, the pirnion runs at 75 rpm and addendum is equal to one module.For these condetions compute: t- The number of teeth on each gear so that interfarance is just avoided. 2 The length of path and arc of contact. 3 The number of pairs of teeth in contact. + The maximum value of siding velocity. S the transmited power is 5 KW, what is the acpled torque on pirion and wheel.
Graphical Displacement Diagrams 9-1. A cam is required for an automated transfer mech- anism. The cam follower must rise outward 1.0 in. with constant velocity in 3.0 s, dwell for 0.5 s, fall with constant velocity in 2.0 s, and then repeat the sequence. Determine the required speed of the cam and graphically plot a follower displacement diagram.
Show complete solution.
In a sharper the cutting tool has a stroke of 16 in. the cutting stroke takes twice the time required for the return stroke. If it is desired to obtain an average speed during the cutting stroke of 35 fpm, What must be the rpm of the driving crank?
correct ans: 60mm
3. A motor has pinion gear with 14 teeth and is meshed with a gear with 52 teeth. The gear is attached to a shaft that drives an 85mm diameter wheel. If the motor spins at 1750rpm's, what is the speed of the vehicle in m/s?
what rpm and feed rate would you use if the shaft was 6 inches and made of stainless steel?

SEE MORE QUESTIONS

Recommended textbooks for you

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

Precision Machining Technology (MindTap Course Li…

Mechanical Engineering

ISBN:

9781285444543

Author:

Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:

Cengage Learning

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning

Automotive Technology: A Systems Approach (MindTa…

Mechanical Engineering

ISBN:

9781133612315

Author:

Jack Erjavec, Rob Thompson

Publisher:

Cengage Learning

Precision Machining Technology (MindTap Course Li…

Mechanical Engineering

ISBN:

9781285444543

Author:

Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:

Cengage Learning

Refrigeration and Air Conditioning Technology (Mi…

Mechanical Engineering

ISBN:

9781305578296

Author:

John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS