8.7 A circular cam of diameter 100 mm has an eccentric axis of rotation which is offset 30 mm from the centre. When used with a knife follower with its line of action passing through the centre of rotation, what will be the difference between the maximum and minimum displacements of the follower?

Q: Q-6: Blocks A and B are identical with each weight of W. If the coefficient of static friction…

A:

Q: dy = m y2 dx

A:

Q: 5. ving gea Sun gear Arm planet gear The picture shows planetaury gear set : a A ssume the sun gear…

A: Given, 2 Sun gear 3 Arm 4 Planet gear 5 Ring gear T2=30T4=27 N5=0N2=101 rev/min

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: 4 5/8" as meters

A: Given-4 5/8" or 4 5/8 inch To find-change the length into meter

Q: ?What is the final reading of Vernier caliper from the figure given below 10 30 40 50 20

A: The main scale reading =5mm Vernier scale reading=0.775mm

Q: part1 and part 2 are correct

A: Process 3-4s : Isentropic expansion process.Process 3-4a : Actual expansion process.Process 4a-1 :…

Q: What is the NCTM Position on the Metric System? What is your personal position on the Metric System?…

A: The National Council of Teachers of Mathematics (NCTM) supports the use of the metric system in…

Q: Determine the magnitude of the resultant force FR = F₁+F₂ and its direction, measured clockwise from…

A:

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: The tooth height is defined by the sum of addendum and the dedendum Select one: True False

A: Tooth height in gear is defined as the radial distance between the addendum and dedendum circle of…

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: 5 kips 3'-0" 3 kips 3'-0" 8 kips + 5'-0" The net force acts on this system is 12 kips 2'-0" 2 kips

A: Given:A simply supporetd beam with the following forces acting on it:5 kips, 3 kips, 8 kips, 12…

Q: Tolerance Maximum Limit Minimum Limit 57/8" 7'9 1/16" 16.76" 5 13/32" 7'8 15/16" 0.03" 0.007" 0.904"…

A: It is required to complete given table

Q: y h с b bh .1

A:

Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something.…

A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior…

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: Try square is a measuring tool used to measure the straightness and squareness of a workpiece.…

A: The square of the measure consists of two main elements, the blade, often referred to as a beam or…

Q: Members ABC and DEF are joined with steel links (E = 200 GPa). Each of the link is made of a pair of…

A:

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: Mercury has a uniform coefficient of expansion Select one: O True O False

A:

Q: A mass of 25 lb is applied at the end of a 2-inch-diameter rod shown in Figure P2. If the modulus of…

A:

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: In order to measure an external tapered angle you must have A. The sine bar and gage blocks B. Two…

A:

Q: In straight bevel gear, the teeth are parallel to the axis of the gear Select one: True False

A:

Q: now the 12-tooth gear turn?

A:

Q: how to read the vernier in inche? what is the reading in inch 1/128in 10 20 30 40

A: It is required to read the vernier

Q: Outside calipers are used for measuring diameters of holes. Select one: True False

A: Outside calipers are used for measuring diameters of holes. Answer: False

Q: Identify the part not belonging to micrometer. Ratchet Clamp O Locknut Frame

A: Given :-  Identity the part not belongung to micrometer Ratchet  Clamp  Locknut Frame

Q: Z is incorrect

A:

Q: A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: True…

A: A micrometre is a precision measuring instrument, with 50 division on the thimble. Select one: True…

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: The feature of saw blade geometry that allows the blade to cut a kerf that is wider than the blade…

A: A feature is responsible when a blade cut a kerf which is wider than the blade itself.

Q: By and bx are labeled wrong

A:

Q: FGI and FKJ correct but incorrect afterwards.

A:

Q: Read the following inch vernier caliper setting 8. 1/128in

A: Solution:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.