Answered: 2. Compute the maximum shear stress and…

2. Compute the maximum shear stress and maximum STRESSES flexural stress of the beam shown in the figure. IN BEAM 30 KN/m 1 m 1 m 30 KN 30 KN 20 KN/m 1 m 250 mm 200 mm 200 mm 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the maximum shearing stress and bending stress for the beam loading shown. Box your…

Q: The simply supported beam in Figure below has a rectangular 3kN w = 1.5 kN/m cross section 100 mm…

A: Finding out maximum stress.

Q: 1 - Determine the maximum shearing stress in the beam for the loading shown in the figure. The same…

A: Given Data Determine the maximum shear stress.

Q: Determine the flexural stress and shear stress of the beam loaded as shown in the figure.

Q: For the beam shown, determine the maximum flexural stress and indicate where it is located both on…

A: Maximum flexural stress will be at a point where bending moment is maximum And in section at a point…

Q: 4. If the moment acting on the cross section of the beam is M = 4kip.ft, determine the maximum…

Q: figure below: 1. Drive the shear force and bending moment equation and then draw them 2. Find the…

Q: 1. For the beam loaded as shown, find the maximum tensile and compressive flexure and shearing…

A: To determine:- Maximum flexural stress (Tensile and Compressive)- Maximum shear stress

Q: Problem 2. Determine the minimum height h of the beam shown in the figure if the flexural stress is…

A: Flexural stress The tensile strength of concrete beams or slabs is measured in terms of flexural…

Q: If the beam is subjected to shear force of V = 12.5 kN as in the figure below, calculate the value…

Q: 2. For the beam shown, determine the following: a. Maximum tensile stress in the beam. b. Maximum…

Q: 20 mm 60 mm 20 mm Figure Q4 - Beam Cross-Section ws oz ww 09 20 mm

Q: A simply supported beam is carrying a unıform load. It the beam prop below, what is the final stress…

A: Introduction: Prestress of concrete is basically concrete in which internal stress of suitable…

Q: Properties: Beam width = 285mm %3D Beam height = 412 mm Concentrated load = 29.89 kN Span of the…

Q: Figure 1 shows a cantilever beam subjected to two point loads (Figure 1a) and the cross section a-a…

A: Given that: NOTE: As per our answering guidelines, we can only answer 1…

Q: 10. Calculate the normal stresses at points A, B, C and D (at section A'A') for the beam shown…

A: To find out the normal stress at point A, B, C and D.

Q: For the beam shown in Fig. Determine the value of the distributed load W if the maximum shear stress…

Q: A T-section distributed beam supports a load w = 88 kN/m (figure 1). 1. Calculate the resulting…

A: For T beam with load carried 88 KN/m 1. - Calculation of resulting internal forces at A 2. -…

Q: Find the bending moment and shear force diagrams for the following beam. What is the location and…

A: Shear force at A= Reaction at A=13kNShear force to the right of A = 13KNShear foece to the left of B…

Q: 6. Assume the beam in example 5 has a cross section similar to the figure shown below. Determine the…

Q: Problem 2 For the cross-section shown below, Mz = 150 kN.m and My = 250 kN.m. Determine the maximum…

Q: 5 kN 5 kN - 5 kN/m B I m 1m 1 m

A: Given, b = 100 m h = 250 mm

Q: A W310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

A: The stress that is caused due to the bending moment of the structure is known as bending moment. The…

Q: 16 KN 12 KN/m 350 mm 5 m 5 m 175 mm

A: Flexural stress : Flexural stress can be calculated from Bending Equation Bending Equation : MI=Fy M…

Q: For the beam shown below, draw bending stress distribution along the depth of beam at free end. 50…

A: Given data Point load Cross sectional area Length

Q: Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa

A: Shear force at section 1-1: V11=-30×2=-60 KN Moment of Inertia (I): I=0.2×0.5312=2.0833×10-3…

Q: A steel beam is subjected to a maximum shear force of 80 kN. The cross-section of the beam is shown…

A: Dimesions of beam areFlange thickness =40mmFlange width =200mmWeb thickness =20mmWeb depth…

Q: Example 4 The simply supported beam in Figure below has a rectangular 3kN cross section 100 mm wide…

A: To find maximum bending stress

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

2. Compute the maximum shear stress and maximum
STRESSES flexural stress of the beam shown in the figure.
IN BEAM
30 KN/m
1 m
1 m
30 KN 30 KN
11m 11m
20 KN / m
250 mm
200 mm
200 mm
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 13 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure 3a shows the loading, shear force diagram and bending moment diagram of a simply-supported beam with its cross-section shown in Figure 3b. Calculate the maximum bending stress in tension, the maximumbending stress in compression and the maximum shear stress in the beam.
Question 2. resultant internal shear force of 18 kN. A beam has a rectangular cross section and it is subjected to a a) Determine the maximum shear stress in the beam. y A 40 mm 200 mm z 18 kN 140 mm
2. Find the largest intensity of uniformly distributed load w that can be applied if the allowable bending stress is 120 Mpa of the box beam shown. 300 mm 50 mmT W 250 mm 3.0 m 3.0 m 3.0 m R2 R1 50 mm 50 mm 200 mm 50 mm
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 465 mm². Determine the average axial stress in each bar. 85 kN 56 kN 2 m D 1m 1 m E 1m 1m F LL
The beam below has a height of 6in and a width of 3in. What is the maximum shear stress (in psi) in the beam?
1. Determine the maximum compressive and tensile stress in beam AB as shown in the figure and draw the stress distribution over the cross section at this location. 25 kN/m 5m 50 KN 5m 4 m 50 KN 150 500 450 150
For the overhanging beam loaded as shown, determine the maximum values of flexural stress and horizontal shearing stress developed
Question 2 A simply supported beam of a channel section (see Figure Q2) is loaded by a vertical point load P= 10 kN (acting upwards) at mid-span. The length of the beam is L=3 m, the overall width and height of the section are of the same value a 50 mm, and the thickness of all three parts of the section is t= 10 mm. Find the value and location of the maximum shear stress in the beam. Figure Q2
A simply supported beam is subjected to twopoint loads, each P = 500 lb, as shown in the figure.The beam has a cross section of 6 X 12 in. Find thestate of plane stress at point C located 8 in. below thetop of the beam and 0.5 ft to the right of support A.Also find the principal stresses and the maximumshear stress at C.
1. For the beam showing in the figure, consider section n-n and determine; (a) The largest shearing stress in that section (b) The shearing stress at point a. 0.3 m 40 nim 10 KN 12 imm 150 mm 12 mm 200 mm 15 in
Determine the flexural stress and shear stress of a rectangular beam loaded as shown in the figure below.