Answered: 20 mm 60 mm 20 mm Figure Q4 - Beam…

Engineering

Civil Engineering

20 mm 60 mm 20 mm Figure Q4 - Beam Cross-Section ws oz ww 09 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 4-m span simply supported beam carries a uniformly distributed load of 45 KN/m over its entire length. The cross-section is as shown in figure. Determine the maximum bending moment along the length of the beam (in KN-m). Determine the maximum moment of area of the cross-section (in mm3). Determine the maximum shearing stress in the beam (in MPa). Determine the maximum shear force along the length of the beam (in KN). Determine the maximum bending stress in the beam. (in MPa).
A simply supported wood beam carries a concentrated load of P = 8200 lbs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 5.5 in. and a depth of d = 14 in. At section a-a, which is xa = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point K, which is located yk = 4.5 in. below the centroidal z axis. H y Ун a Ук a B K L2 Answer: TK = i psi
Steel structure design
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a – a is located at x = 0.7 m from B. (a) At section a – a, determine the magnitude of the shear stress in the beam at point H. (b) At section a – a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length
A simply supported wood beam that is 4.2 m long carries a 49 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 130 mm, d = 420 mm, a = 65 mm, and c = 40 mm. Section a–a is located at x = 0.7 m from B.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span.(d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
only typed solution accepted
Considering the fully restrained beam shown in Figure 2 where E = 200 GPa and I = 2x10^9 mm^4 If P = 70 kN, M = 100 kNm, L = 12 m., and G = 40 degrees. Use either the virtual work method or the method of consistent deformation and state what you use with a complete solution. thank you. 1. Determine the maximum positive and negative shear that is acting on the beam. 2. Determine the maximum positive and negative moment that is acting on the beam 3. Determine the maximum deflection of the beam. 4. If the maximum deflection is limited to 10mm, determine the diameter of the circular beam required.
A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.9 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 160 mm. 280 mm b. 170mm
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 14 cm as width, 23 cm as depth, and inner thickness as 1 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
A T-shape beam is subjected to a vertical shear force of V = 30 kN. The beams centroid is located 211.1 mm above the bottom surface of the beam, and the moment of inertia is l₂ = 48.7 x 106mm4.[b = 178 mm, h = 300 mm, t₁ = 12.7, tw = 9] b h tw Determine the shear stress in the flange at the intersection of the flange and the web. 6.96 MPa 7.6 MPa 2.94 MPa 4.3 MPa 6.09 MPa
Question: Calculate the vertical reaction force at G and the vertical reaction force at A.