2. Compare the heat loss from insulated and uninsulated copper pipe (k-400 W/m K) under the following conditions. The pipe has an internal diameter of 10 cm and an external diameter of 12 cm. The inside surface temperature of the pipe is at 110°C. The pipe is located in a space where its outside surface temperature was maintained at 30°C. The insulation available to reduce heat losses is 5 cm thick and its conductivity is 0.20 W/m K. If the furnace for heating the fluid in the pipe operating at an efficiency of 85% using natural gas priced at Cg = Php 1.00/MJ, what is the daily cost of heat loss per meter of pipe?

2. Compare the heat loss from insulated and uninsulated copper pipe (k-400 W/m K) under the following conditions. The pipe has an internal diameter of 10 cm and an external diameter of 12 cm. The inside surface temperature of the pipe is at 110°C. The pipe is located in a space where its outside surface temperature was maintained at 30°C. The insulation available to reduce heat losses is 5 cm thick and its conductivity is 0.20 W/m K. If the furnace for heating the fluid in the pipe operating at an efficiency of 85% using natural gas priced at Cg = Php 1.00/MJ, what is the daily cost of heat loss per meter of pipe?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wall with a brick and concrete layer is shown in the figure. The wall has a length of 15 m and 6 m high. The brick (k = 1.3 W/m-K) has a thickness of 75 mm and the concrete (k = 2 W/m-K) is 150 mm thick. Determine the total heat resistance, the heat transfer rate through the wall, and the temperature of its inner surface for a day during which the room is maintained at 20°C while the temperature of the outdoors is 32°C. Take the convection heat transfer coefficients on the inner and outer surfaces of the wall to be 12 W/m²-K and 18 W/m²-K, respectively, which includes the effects of radiation. Round off your final answer to three (3) decimal places. (20 pts.) Tooout Outdoor Brick Concrete Wall Heat Transfer, Q (W) = Total Heat Resistance, RT (K/W) = input: 2.01234x10^-3) T₂ Inner Surface Temp, T2 (°C) = Toin Indoor (5 decimal places - example
A 1-in Sch 40 stainless steel pipe with a thermal conductivity of 45 W/m-K can move 1,000 kg of saturated steam per hour at 150 °C. Refractory material 0.25 inches thick with a thermal conductivity of 0.025 W/m-K insulates the pipe. At a temperature of 25 °C, the pipe is exposed to the outside air. There is a 1135 W/m2 internal heat transfer coefficient.40 W/m2-K is the outside heat transfer coefficient, whereas -K. Suppose that only the radial direction is involved in steady-state heat transfer and that radiation effects are negligible. ✓ Determine how much heat is being lost through these pipes to the environment.a. 399.1 W/mb. 1525.0 W/mc. 618.4 W/md. 1128.7 W/me. none of the above √ How about the insulated pipe's surface temperature?a. 118.5 °Cb. None of the abovec. 101.5 °Cd. 216.3 °Ce. 292.2 °C
The inside surface of an insulation layer is maintained at 350°C and the outside surface dissipates heat by convection and radiation to air and wall, respectively. The temperatures of air and wall are 15 °C. The insulation layer has a thickness of 10 cm and a thermal conductivity of 15 W/m.K. What is the value of the heat transfer coefficient at the outside surface of the layer, if the temperature at the outside surface should not exceed 225 °C? (The emissivity and the width of the surface are 0.3 and1 m., respectively. o-5.67x10-8 W/m²K*). Tw=15°. T=225°C ɛ=0.3 ТЬ3350°C To=15°C h.=? 10 cm
700 W/m3 electrical heat is generated in a large plane wall whose one side is insulated while the other side is subjected to convection. The thermal conductivity of the wall is (k W/m.K) and the convection heat transfer coefficient is (h = 17 W/m?K). Determine the location and the value for the maximum temperature and the minimum temperature in the plate for steady one-dimensional heat transfer. Assume T. = 25°C. A=1 m?; L= 25 cm). = 20
A 12cm outside diameter and 10cm inside diameter cast iron pipe with conductivity of 80W/m-K has 4 cm of polystyrene insulation with conductivity of 0.027W/m-K. Saturated steam at 500degC is flowing through pipe and the outside surface temperature is 60degC. Determine the temperature of the outside surface of the pipe.
A cast iron pipe (k = 80 W/m - oC) whose inner and outer diameters are 5 cm and 5.5 cm respectively is coverd with a 3 cm thick glass wool insulation (k = 0.05 W/m - oC) The temperature at the inner surface of the pipe is 320 oC and the interface temperature between the pipe and insulation is 300 oC. Determine the surface temperature of the insulation.
Consider the base plate of a 750-W household iron with a thickness of L=0.6 cm, base area of A=170 cm2, and thermal conductivity of k=22 W/m.oC. The inner surface of the base plate is subjected to uniform heat flux generated by the resistance heaters inside. When steady operating conditions are reached, the outer surface temperature of the plate is measured to be 85 oC. Disregarding any heat loss through the upper part of the iron, (a) express the differential equation and the boundary conditions for steady one-dimensional heat conduction through the plate, (b) obtain a relation for the variation of temperature in the base plate by solving the differential equation, and (c) evaluate the inner surface temperature.
The external brick wall of a building has a surface area A of 830 m2 andthickness δ of 300 mm. The wall has a thermal insulation on its outer surface. The thermal conductivity of concrete k is 1.6 W/m K and of insulation is 0.04 W/m K. The indoor and outdoor air temperatures are ti = 21°C and to = 3°C, respectively. The heat-transfer coefficients are hi = 14 W/m2K (on the inner surface) and ho = 20 W/m2K (on the outer surface). Determine (1) the rate of heat loss through the wall without insulation and (2) the thickness of the insulation required to reduce the rate of heat loss by 60%.
Radioactive material is stored in a spherical vessel with a diameter of 3.7 m, and the center of the vessel is 11 m below the ground. The vessel is surrounded by a 10.2 cm thick layer of rigid foam insulation (k = 0.026 W/m-K). The radioactive material releases heat at a rate of 1000 W/m³. The surface of the soil it's buried in (k = 2 W/m- K) is exposed to wind with a temperature of 20°C and a convection coefficient of 17 W/m²-K. What is the temperature of the surface of the tank?
The outer surface of an oil heater at a uniform temperature of 100°C is to be filled with straight rectangular fins having a uniform thermal conductivity of 180 W/m.K. The ambient air temperature is 25°C and the heat transfer coefficient is 100 W/m².K. The fin thickness t-1mm, width w= 1m and its length is L= 10mm. If the heat transfer from the tip of the fin by convection, calculate fin efficiency and effectiveness. Tь =100 с Too = 25°C h = 100 W/m2-K L = 10 mm Air k= 180 W/m-K t = 1 mm
The outside temperature on a particular winter's day is 0°C. Consider two identical houses, each of external surface area 200 m² and internal temperature 20°C. The walls of the first are constructed of a single layer of brick, of thermal conductivity 1 W m-1 °C-1 and thickness 20 cm. What is the heat flux Q out of this house? What is its rate of heat loss in Watts? The walls of the second house are constructed of two layers of brick, each 10 cm thick, and a layer of insulation, also 10 cm thick. The insulation is made mostly out of air, thermal conductivity 0.01 W m of heat loss from this house? How different would your answer be if you neglected the layers of brick in this calculation? -1 °C-1. what are the heat flux and the rate
The thermal conductivity of a solid material can be determined using asetup similar to the one shown in the accompanying figure. The thermocouples are placed at 2.5 cm intervals in the known material (copper alloy, k - 52 w/m.k) and the unknown sample, as shown. The known material is heated on the top by a heating element, and the bottom surface of the sample is cooled by running water through the heat sink shown. Determine the thermal conductivity of the unknown sample for the set of data given in the accompanying table. Assume no heat loss to the surroundings and perfect thermal contact at the common interface of the sample and the copper.