2. A hollow cylinder 2 m long has anoutside diameter of 50mm and insidediameter of 30mm. If the cylinder iscarrying a load of 25 KN. FInd the stress incylinder , also find deformation of thecylinder E=100 Gpa.

Answered: Image /qna-images/answer/37b00893-5ceb-4573-bab6-1eeb32b37663.jpg

Answered: 2. A hollow cylinder 2 m long has an…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.8P: - A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s...

See similar textbooks

Similar questions

correct or wait for dislikes
I need full details solution and please don't provide handwirrite solution.
A tie rod of ¼ inch diameter is used to hold a plaster wall in place. The tensile stress in the rod caused by load P is 20 ksi. Find the diameter “d” (to the nearest 1/6 inch) of the washer that keeps the bearing stress between the plaster and the washer from exceeding 300 psi.
A short cylindrical cast iron post supports a compressive load of 20 tons (40 kips). If the factor of safety is taken equal to 10, find the diameter of the post. Ultimate stress for compression is 80,000 psi. Neglect slenderness ratio and no buckling. (2.52in)
I have been stich on this problem for a while is seems the internal force of section one should be equal to the reaciton force at D but that does not seem to be the case. how to I solve this. Determine the internale force and the change in tlength of seciton (1) of axial member CDE.
A Mild Steel wire 5 mm in diameter and 1 m long. If the wire is subjected to an axial tensile load 10 kN find its extension of the rod. (E = 200 GPa)
A hollow aluminum cylinder made of 2014-T4 has an outside diameter of 2.50 in. and a wall thickness of 0.085 in. Its length is 14.5 in. What axial com- pressive force would cause the cylinder to shorten by 0.005 in.? What is the resulting stress in the 3-25. aluminum?
Find the safe value of the axial load P in a circular column consists of circular 125mm wooden post and a 200mm x 200mm concrete footing separated by a steel plate. The working stresses are 15 MPa for wood and 18 MPa for concrete.
A steel bar 2m long, 20 mm wide and 10 mm thick is subjected to a pull of 20 kN inthe direction of its length. Find the change in thickness. Take E-200 GPa and Poisson'sRatio 0.30
Big and clear handwriting with the drawing please. Make sure calculations and answers are accurate please. THANK YOU
An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, a = 12 x 10 C, and for aluminum assume E= 70 GPa, a= 25 x 10rC. Ans. o= 9 MPa, o = 15.5 MPa %3D 200 kN 500 mm 80 mm 85 mm 141 mm Fig. 1-29
Question Two A steel flat of thickness 10 mm tapers uniformly from 60 mm at one end to 40 mm at other end in a length of 600 mm. If the bar is subjected to a load of 80 kN, find its extension. Take E = 2 x 10 MPa. What is the percentage error if average area is used for calculating extension?

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the cylinder is carrying a load of 25 KN. FInd the stress cylinder , also find deformation of the