correct or wait for dislikes 2. A hollow cylinder 2 m long has anoutside diameter of 50mm and insidediameter of 30mm. If the cylinder iscarrying a load of 25 KN. FInd the stress incylinder , also find deformation of thecylinder E=100 Gpa.

Answered: Image /qna-images/answer/5e04cf8e-b8f4-4902-b060-64a09b5f58ae.jpg

Answered: 2. A hollow cylinder 2 m long has an…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

is the method of skewness used in ansys
Need questions 13, 14, 15 explained and answered please.
How did you get the Tsat values
1.2 Please select all the correct statement blow. A. Retaining rings are inappropriate to retain hubs and bearings onto shafts. B. During shaft design, the locations with the minimum torque and moment should be identified. C. A rivet can always provide a much stronger attachment than a bolt or screw of the same diameter. D. Power screws are used to convert the rotary motion of either the nut or the screw to relatively slow linear motion of the mating member along the screw axis. E. Single-row ball bearings (as shown in the figure below) can carry a significant amount of trust load and can carry more trust load than roller bearings (as shown in the figure below). single-row ball bearing Explanation: roller bearing
Surface plate is a marking device designed to make quicker and finer adjustments. Select one: True False
Centre punch is a marking tool used in workshops for the purpose of making indentations on the workpiece with an included point angle of 900. Select one: True O False
In section views, match patterns should be drawn parallel to one of the edges of the part. True? A. Yes, always B. Optional C. Never Section views must retain the same scale as the part from which they are created. True? A. Yes, true B. No, they may be scaled
2 5 What is the shape and size of this tolerance zone? 1.25 0.50 Diam +/-0.002" 0.010
If the answer is no can anything be done to save the part?
Question 3 The Extrude Cut feature in SOLIDWORKS can be used to create both through holes (holes that go all the way through a part) and counter bore holes (holes that do not go all the way through a part), such as the holes shown in the 2-dimensional image below. True False Counterbore
The term "maintenance" refers to maintaining all of the systems and features in working order. * as close as possible to the original O design purpose of the manufacturer tons as close to the manufacturer's original design purpose as impossible as impossible to the manufacturers original design intent tons. as possible to the manufacturers unoriginal design intent tons skip Punctures are- a small hole in a tire resulting in an get- away of air a large hole in a tire resulting in an get- away of air a small hole in an engine resulting in an escape of air a small hole in a tire resulting in an get- away of oil Skip
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

2. A hollow cylinder 2 m long has an outside diameter of 50mm and inside diameter of 30mm. If the cylinder is carrying a load of 25 KN. FInd the stress in cylinder , also find deformation of the cylinder E=100 Gpa.