2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the maximum bending load on this sample.

2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the maximum bending load on this sample.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3-1. A concrete cylinder having a diameter of 6.00 in. and gage length of 12 in. is tested in…

Q: ncrete in terms of cube strength. (Use the related charts provided at

A: as per IS:8900, Clause 5.1.1(TESTS FOR TWO OR MORE OUTLIERS , AT LEAST ONE OUTLIER AT EACH END, 16…

Q: The cross section of a beam constructed using Grade 50 concrete (Ec = 34800 MPa) is 300 mm x 500 mm…

Q: 4N20 450 mm 390 mm 300 mm

Q: A cylindrical block is 35 cm long and has a circular cross-section 10 cm in điameter. It caries a…

A: Solved below

Q: Two beams, A and B, made with the same material are to be subjected to a three-point bending test.…

Q: The piece of wood shown below was used in an experiment. During the test it sheared parallel to the…

A: Shear stress is the force that causes deformation by sliding along a plane of material. When the…

Q: 2. (a). Determine the cracking moment for the beam section shown. Use fc = 21 MPa. (b). What is the…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Two beams, A and B, made with the same material are to be subjected to a three-point bending test.…

A: Given,for beam A,lengthL1=25 inwidthb1=1.25 indepthd1=0.5 infor beam B,lengthL2=1.5 inwidthb2=1.5…

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: A hollow aluminum circular cylinder, 32 cm tall with a 5.0 cm outside diameter and a wall thickness…

A: Step 1

Q: A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50mm and initial…

Q: Find the reading of the device in units kn to check the compressive strength of a cubic concrete…

Q: Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from…

Q: A tension test was performed on a steel specimen having an original diameter of 0.503 in. and gage…

Q: Assuming elastic behavior, why does the maximum shear stress always correspond to the neutral axis…

A: Given data:

Concept explainers

Test for Determination of Shear Strength

The term shear strength is often associated with the soil. Shear strength is defined as the resistance to the deformation of soil particles due to the continuous action of shear stress. In short, shear strength is the maximum shear stress that a soil can sustain.

Question

2. A bending test is performed on a concrete prism sample with dimensions of 4x4x16 cm. When the
distance between the supports is 10 cm, the maximum load value measured is 2256 N. Calculate the
maximum bending load on this sample.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Test for determination of shear strength

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Procedure: 1. Measure the dimensions of the specimen and the record them in the date sheet 2. Turn the specimen on its side with respect to its position as molded and center in on life support blocks. 3. Center the loading system in relation to the applied force. 4. Bring the load applying-block in contact with the surface of the specimen at the center and apply a load between 3 and 6% of the estimated load. 5. Grind cap, or use leather shims on the specimen contact surface to eliminate any gap in excess of 0.004 inch (0.10 mm). Gaps in excess of 0.15 inch (0.38 mm) shall be eliminated by capping or grinding. 6. Apply the load on the specimen continuously and without shock. The load shall be applied at the constant rate to the breaking. Apply the load at such a rate that constantly increases the extreme fiber stresses between 125 and 175 psi/min. (0.86 and 1.21 MPa/min) when calculated until rupture occurs. 7. Take three measurements across each dimension (one at each edge and at the…
A tensile test was carried out on a metal specimen. The gauge length of the specimen was 96 mm and the initial (original) cross sectional area was 17.36 mm^2. The final (fractured) length was 107.4 mm and the final cross- sectional area was 16.40mm^2 . Determine the percentage elongation and percentage reduction in area of the specimen.
What would be the average compressive strength of concrete if the load at failure of the 3 trials are 55, 100 kg, 54, 800 kg, and 55, 200 kg. Diameter of the sẫmple is 6". о 30.6 MPа о 31.6 MPа о 30.1 МPа о 31.1 MPа
Problem 20.2 Concrete has a notable capacity against compression stresses but very little capacity against tension stresses (it cracks easily). One strategy to counteract this weakness in tension involves using wires or rods to prestress the concrete beam in regions where flexural tension can be anticipated. Consider the simply-supported beam shown, which has a rectangular cross section of 18" x 12". If concrete has specific weight of 150 pcf (pounds per cubic foot) determine the required tension in rod AB, which runs through the beam so that no tensile stress is developed in the concrete at its center section a-a. Neglect the size of the rod and any deflection of the beam. a 16 in. B 2 in. 18 in. 6 in. 6 in. -4 ft- - 4 ft Tip: the beam's self-weight causes and internal moment at the midspan section and therefore flexural tension stress at the bottom of the beam. When the rod is tensioned it applies both an axial stress and a bending moment (since it is applied eccentrically on the…
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.
Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 50*10 deep reinforced with bars 20-mm in diameter enclosed with 10-mm-dia stirrups when the tensile steel strain is 0.008 and concrete compeession strain is 0.003. f’c = 20 MPa express your answer in 2 decimal places only in mm
Please fill in all sections
Problem 1.4. A tensile test was conducted on a mild steel bar. The following data was obtained from the test : (i) Diameter of the steel bar (ii) Gauge length of the bar (iii) Load at elastic limit (iv) Extension at a load of 150 kN. (v) Maximum load (vi) Total extension (vii) Diameter of the rod at the failure Determine : (a) the Young's modulus, = 3 cm = 20 cm = 250 kN = 0.21 mm = 380 kN = 60 mm - 2.25 cm. (c) the percentage elongation, and (b) the stress at lastic limit, (d) the percentage decrease in area.
In Tables 5A and 5C of the NDS Supplement, why is there only one value of reference bending design stress, Fby, about the Y axis while there are two values for reference bending design stress, F*bx and F bx, about the X axis? The layup and orientation of lams are symmetric for bending about the X axis The layup and orientation of lams are symmetric for bending about the Y axis The two values for Fbx refer to Western Species and Southern Pine glulam members The flexural response is different for members subjected to tension (+) or compression (-)
Calculation: Compressive Strength (CS) = P/A Where: CS = compressive strength of the specimen, psi (KN/m²) P = maximum load, Ib (KN) A = cross-sectional area of the specimen, inches (m²) Gross Area: Tabulated Data and Result Trial No. b (m) w (m) A (m²) P (kN) CS (kN/m²) 1 0.4 0.15 0.06 150 2 0.4 0.15 0.06 180 3 0.4 0.15 0.06 140 Net Area: Tabulated Data and Result Trial No. A (m²) P (kN) CS (kN/m2) 1 0.0296 150 0.0296 180 0.0296 140
How does load testing differ from stress testing in terms of performance measurement?
A compact tension specimen is tested according to ASTM standard E399. The load displacement curve is shown in the Figure below with PQ= 120 kN (Type 1 curve). The specimen dimensions are B=0.5 cm, W=10 cm, and “a” =5 cm. If the materials yield stress is 600 MPa are the conditions correct for a valid K1C measurement? Please look up McEviley’s textbook on the thickness criterion for a valid fracture toughness value.