2- The below figure shows three-point bending test of a bone a) Determine the shear force diagram using the graphical method b) Determine the moment diagram using the graphical method c) If the bone can be assumed as a uniform hollow cylinder, determine the maximum normal stress due to bending in the bone 4 For hollow : Ix = Iy =" (r,* – r,*) 200N Cross 2cm 15cm 2cm > 15cm section 2cm 4cm 34cm 100N 100N 2.55 MPа) (Answers: c)omax

2- The below figure shows three-point bending test of a bone a) Determine the shear force diagram using the graphical method b) Determine the moment diagram using the graphical method c) If the bone can be assumed as a uniform hollow cylinder, determine the maximum normal stress due to bending in the bone 4 For hollow : Ix = Iy =" (r,* – r,*) 200N Cross 2cm 15cm 2cm > 15cm section 2cm 4cm 34cm 100N 100N 2.55 MPа) (Answers: c)omax

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4
The question is in the picture. Thanks
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1700 N, T = 4167 Nm, a = 0.94 m, b = 1.07 m, c = 0.98 m, w = 33 mm, and h = 79 mm . Round off the final answer to one decimal place. P T W Y U A/O А h B k a b C C | 1 D
Part 2,3,4
In the following structure, determine the stress in each bar. Indicate whether the stress is tensile or compressive. The area of each bar is indicated in this figure. Answ. AB = 8.33 ksi (C), BC = 8.33 ksi (C), DE = 25 ksi (T), AD = 16.6667 ksi (T), BE = 8.33 ksi (T), AE = 27.77 ksi (C)¸ CE = 10.41667 ksi (T).
Problem 6.42 Consider the truss (Figure 1). Suppose that F = 14.5 kN Figure 1 4 kN of 1 6 kN H B m G 2 m 9 KN C -1.5 m 1.5 m 1.5 m 1.5 m 1 m D > 6 kN E Part A Determine the force in member BC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBC = Submit Part B FHC = D μA Submit Value My Answers Give Up Determine the force in member HC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units μA Value Units ? My Answers Give Up ? Part C Determine the force in member HG. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
bb new 10
Q4/ For the lower limb prosthesis figure 1 below, find the maximum stress at point (A) due to the ground reaction force which can reach to 875N. The shank cross section area dimensions are (inner D=20mm, outer D=24mm), the distance between the ground reaction force and the socket center is 1.5cm. A TUBE IS VERTICAL FOOT IS FLAT 2-3 PLUMBLINE IS MEDIALLY DISPLACED
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 480 psi in size. (a) Determine the stresses o,, Oy, and the magnitude of Txy and show them on a stress element. (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16). y
Part A In (Figure 1), r = 30 mm. Locate the centroid a of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. T = 0 mm Submit Previous Answers Correct Figure < 1 of 1 Part B Locate the centroid ī of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. HẢ ? 150 mm = Value Units Submit Previous Answers Request Answer 50 mm 100 mm 100 mm 50 mm