2) If the beam is subjected to a shear of V = 15 kN, determine the web's shear stress at A and B. Indicate the shear-stress components on a volume element located at these points. Show that the neutral axis is located at y = 0.1747 m from the bottom and INA = 0.2182(10³) m². 30 mm 250 mm 30 mm 200 mm 25 m V B 125 mm

2) If the beam is subjected to a shear of V = 15 kN, determine the web's shear stress at A and B. Indicate the shear-stress components on a volume element located at these points. Show that the neutral axis is located at y = 0.1747 m from the bottom and INA = 0.2182(10³) m². 30 mm 250 mm 30 mm 200 mm 25 m V B 125 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the previous problem, determine the shear stress 30 mmabove the neutral axis.
Asap
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.3 mm and upward by v = 5.2 mm to new position Q'. Determine the shear strain y at corner Q'after deformation. Use c= 665 mm, a = 23°, and B = 67°. P R Answer: Y = i prad
A force of 521 kN is applied at joint B to a system of two-pinned joined bars shown in the figure. Determine the required cross-sectional area of the bar BC if the allowable stresses are 175 MPa in tension and 74 MPa in compression. 521 kN B 1.5 mt 1.5 m 3.0 m 3.0 m
The solid circular section EF rod in the figure is fixed to the wall at point F. Forces P1 = 1 kN, P2 = 2 kN were applied from point D of the DE rod, which is rigidly connected to the rod. Calculate the stress states occurring at points A and B and show them on the small volume elements removed from these points. The diameter of the EF rod will be taken as d = 50 mm. Do not give answer in image and hand writing
Calculate the value of Q and t that are used in the shear formula for finding the shear stress at B. 0.2 m Neutral axis Q = y'A' 0.2m 10.2 m Q = A, + 2y,A2 A2 0.2 m yi = 0.3m yz = 0.1m %3D A = 0.2 x 0.6 m? Az= 0.2 x 0.2 m? 0,2 m 0.2 m 0.2 m 0.1 m
len 9
Beam 9: (P = 26 KN - L = 2.0 metres) For the given cross section of the beam, find the magnitude of the maximum compressive bending stress and also the magnitude of the maximum tensile bending stress. What is the maximum shear stress in the beam and where in the beam does it occur? 2P 2P 25 50 25 25 50 125
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 4300 mm² and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A₂ = 2550 mm² and an allowable normal stress of 125 MPa. Assume x₁-23m.x₂-3.9 m.y1 = 1.4 m, and y₂ = 2.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ Answer: Pmax= i| B P ! KN
The bottom of the hollow shaft shown in figure 2 is fixed to a surface acting as a rigid support. Suppose the hollow shaft has an inner radius of r, = 40mm and outer radius r, = 55mm %3D %3D Figure 2 a) Determine the torque T if the maximum shearing stress is not to exceed 60 MPa. b) Suppose that the shaft is solid instead, with the same outer radius. Use the calculated torque T from part a, and determine the maximum shearing stress of the solid shaft due to torque T. c) Why would we still choose a hollow shaft when it will experience higher stress compared to a solid shaft?
14-2.5: The stress-strain curve of the axially loaded bar BC is binary and linear, with ϭA=400 MPa, ϭ=500 MPa ,ꜪA=0.004, Ꜫ= 0.016 . Find the total axial displacement at point C. External loads P1=1.6 kN, P2=1.2 kN, cross-sectional area A=10 mm2, bar dimensions a=600 mm, b=300 mm
1.1