18 Which of the following are types of thread-cutting dies? Multiple Answer (check all that apply) O Taps O Solid O Adjustable O Two-part Adjustable 19 Inch threads are standardized by what? Multiple Choice (select the best answer) O M-series O Unified Inch Standard Unified Thread Standard None of the Above 20 External thread-cutting dies are used to cut an external thread on the outer diamete True/False (select one answer) True False

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: Solidworks 24 threads per inch Units: IPS Mass = 0.0681 pounds Volume = 0.2417 cubic inches…

A: It is asked to create a bolt as shown in the question Make sure the unit system is IPS selected from…

Q: A 29/32 icnh hole must be enlarged to 59/64 inch to insert a bushing. How much wider than the…

A: To find out how much wider the hole will be after enlargement, we need to calculate the difference…

Q: hat are the parts made by cast iron ?

A: Mainly three parts are made by Cast Iron 1. Body 2. Spindle bearing 3. Hand Wheel

Q: 7) Given the ISO metric hexagon socket screws in the figure; select the correct name of the head…

A: For question number 7 the correct answer is option b. As the first figure is of cap screw and second…

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: v thread is:

A: In screw largest diameter is its major diameter

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: Procedure: • Create a detailed thread drawing for the fastener given below. • Save your drawing to a…

A: Kindly refer the next page to see the detailed drawing.

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot           -     3Countersink      -     6Knurl                  -…

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: Thread Fits and 7. Define fit, allowance, tolerance, and limits. Classifications

A: Topic : engineering drawing

Q: Identify the type of milling operation in which the narrow slots or grooves can be produced into the…

A: Solution:

Q: ch Liner (ID 6.270

A:

Q: What is the pitch diameter for an M24 fine-series threaded bolt? O 21.5 mm

A: What is the pitch diameter for an M24 fine-series threaded bolt?

Q: If the diameter with tolerance of the hole is 2.6 ±0.1 mm, which of the following is the safe…

A: Diameter with tolerance the hole =2.6 ± 0.1 mm   To find: Safe diameter and tolerance of the shaft…

Q: & Sharpe gears är ne differential indexing formula, calculate the indexing for the following: EROWN…

A: Given, Simple indexing Gear ratio 40:1 Number of divisions(N) =35   40 revolution of crank=1…

Q: I need questions 5, 6, and 7 answered exactly as the example showed for problem number 1.

A: Note: Since we answer only one question, we will answer the question number 5. Please submit a new…

Q: Write 10 steps of the Procedure for internal thread cutting

A: 1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on…

Q: 268 Threads M30 Ø25 032h6 0.8 Ø30 M20 18 rØ19.5 M24 40 НЕХ. 3 25 Ø15 10 12 M18 X 1.5 V 12 25 90…

A: 8. Length of the threads . 16. Threads

Q: Explain the differences between single and multiple threads. [ Draw and describe the function and…

A: Introduction: Threads are spiral grooves of identical size or shape created on a circular…

Q: 1. If maximum stress is 200Mpa, stress amplitude is 50Mpa, minimum stress is 100Mра. ( ) 2. For the…

A:

Q: Company XYZ are planning to manufacture a rod made from grey iron as in Fig 1. As a production…

A: Coding is the technique of assigning symbols to pieces that are used for communicating media…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Q: What is the MMC of hole "D"?

A: The maximum material condition (MMC) tells the amount of maximum material of the smallest diameter…

Q: Consider the figure shown below, (enter all answers in this format 0.XXX) 4XØ 255 a 005 O 010 B -50…

A: TOTAL POSITION TOLERANCE The GD&T symbol for location tolerance is position tolerance. The True…

Q: The feature of saw blade geometry that allows the blade to cut a kerf that is wider than the blade…

A: A feature is responsible when a blade cut a kerf which is wider than the blade itself.

Q: Using the Brown & Sharpe dividing head with the above standard gears and the differential indexing…

A: Brown and Sharpe is the name of the scientist who discovered the concept of head indexing. Indexing…

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given…

A: Given data: -  The tolerance diameter of hole is Dh = 0.990"/1.010".  The tolerance diameter of pin…

Q: What does the headgear of a mine do?

A: What does the headgear of a mine do?   Headgear or mine headgear is actually the construction…

Q: Consider a thread callout of Dia 0.375-10 UNF-2B. How far will the thread travel if it is…

A:

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…

Q: Add the Correct Answer Calculations 1. 1/4 indicates 2. 20 indicates UN is an abbreviation for Shape…

A: Since you have asked multiple sub-parts only the first 3 subparts are solved for you, If you want…