Given the following thread specification: ½ - 28 UNEF – 2A 1) What is the pitch? __________ 2) How many threads per inch? ________ 3) What class of fit? __________________ 4) What is the diameter? ________________ 5) Completely describe the thread form. ____________________________________

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: A bearing is designated by the number 205. It means that a bearing is of *     a)the double row ball…

A: Type Code and Bearing Name 1       Self Aligning Ball Bearings 2       Spherical Ball Bearings 3…

Q: a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is…

A:

Q: A chain drive is required to transmit a design power of 4.13 kW from a motor to an output shaft. The…

A:

Q: The efficiency of a power screw does nột depend on which of the following variables. Hint: Look at…

A: formula for efficiency of power screw is given byη=Fl2πThere F=load in newtonl=lead T=torquetorque…

Q: Solidworks 24 threads per inch Units: IPS Mass = 0.0681 pounds Volume = 0.2417 cubic inches…

A: It is asked to create a bolt as shown in the question Make sure the unit system is IPS selected from…

Q: hat are the parts made by cast iron ?

A: Mainly three parts are made by Cast Iron 1. Body 2. Spindle bearing 3. Hand Wheel

Q: Question 4 ( For the specimen shown, what will be the maximum stress near the hole region (in ksi)?…

A: Given:w=2.49 int=0.25 ind=1 inN=3350 lb NOTE: According to Bartleyby's guidelines we can answer only…

Q: Limit Gauge loose fit, slide fit, easy sliding fit, running fit Go & No Go Ends O the difference…

A: As per our guidelines we are supposed to answer only one question if multiple questions are asked.…

Q: how would i do the Chamfering for this part on the lathe? what cutting tool would i use  what…

A: Given drawing:

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: What is load-displacement?

A: It is related to a ship or a cargo vessel.

Q: Q3) A student wants to know the linear measurements of a screw thread (in inch), if the student…

A: (A) The thread angle is 55o (B) The screw type is the "Whitworth screw"

Q: Procedure: • Create a detailed thread drawing for the fastener given below. • Save your drawing to a…

A: Kindly refer the next page to see the detailed drawing.

Q: Identify the type of milling operation in which the narrow slots or grooves can be produced into the…

A: Solution:

Q: Refer to drawing 21A044, How many full threads will the extra fine tapped hole contain? (Disregard…

A: In Engineering Drawing, the tapped hole with full threads is denoted in the form of given…

Q: I need help with this.

A: Note:We’ll answer the first question since the exact one wasn’tspecified. Please submit a new…

Q: If the diameter with tolerance of the hole is 2.6 ±0.1 mm, which of the following is the safe…

A: Diameter with tolerance the hole =2.6 ± 0.1 mm   To find: Safe diameter and tolerance of the shaft…

Q: Determine the limits of sizes, tolerances and fundamental deviations for the shaft designated as  40…

A: Given      Shaft designated as 40H8/f7  Therefore,                                       40mm id=s…

Q: Step 1: Given: specific gravity, G=1.7 The objective is to determine: a. density of fluid in…

A: Specific gravity G = 1.7Find(1) Density ρ(2) specific weight ɣ

Q: On the attached drawing, is the allowance between "shaft C" and "hole D" positive or negative?

A: Allowance is the difference between the basic dimensions of the mating parts. There are two types of…

Q: 7. Pitch 8. Length of threads 11. Pitch 16. Pitch

A: Standard designation for Metric thread

Q: Name the 2 types of axial loading?

A: Two types of axial loading are tensile and compressive stress. Both kinds of stresses arise within…

Q: 1. AISI steel designation for plain carbon steel. 2. In GD&T, what does this indicate 3. A fit…

A: Steel designations are the ways to define the different plain carbon steels.

Q: In a tap set, a plug tap is used for final cutting the thread throughout its length after using two…

A: Solution:

Q: Complete the needed calculations and enter the needed values in the given table. All problems are…

A:

Q: ?What are the type of vibration in circular wood saws and fluid pipe, and why

A:

Q: 268 Threads M30 Ø25 032h6 0.8 Ø30 M20 18 rØ19.5 M24 40 НЕХ. 3 25 Ø15 10 12 M18 X 1.5 V 12 25 90…

A: 8. Length of the threads . 16. Threads

Q: What is the LMC of shaft C?

A: The Least material condition (LMC) tells about the minimum material can be used to produce the…

Q: Refer to the Ø.750 dimension. A) Where is the tolerance specified ?…

A: 1—position 2 – the shape of the tolerance zone

Q: What company specification number is given to the material for this part?  2. What is the revision…

A: Engg drawing is a technical drawing that is used to transfer the information from the design to the…

Q: 20 BUTT-2A .688 R. .626 DIA..003 5.50 13 812 6.000 -1.000 UNLESS OTHERWISE SPECIFIED: MATERIAL:…

A: 5. Pitch  6. BUTT is designation for  9. Standard or precision class of fit

Q: I am going to use a Bolt through the .41 DIA holes to align the parts, answer the following: What…

A:

Q: es the specification "8.8" in the standard designation of a bolt mean? Specify values including…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: I need answers to questions 1, 2, and 3 pertaining to the print provided. Note: A tutor keeps…

A: If any changes in the part feature are made, the changes are recorded in the specified format in the…

Q: B. A machine - part needs 14 bolts a How many bo43 are needed For 25 nachine -parts? b. wnat is the…

A:

Q: The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given…

A: Given data: -  The tolerance diameter of hole is Dh = 0.990"/1.010".  The tolerance diameter of pin…

Q: What does the headgear of a mine do?

A: What does the headgear of a mine do?   Headgear or mine headgear is actually the construction…

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…

Q: Draw a product structure tree for a rolling cart using the low-level coding scheme.

A: Given data:  they given items and components and  they ask to draw product strycture tree

Q: Add the Correct Answer Calculations 1. 1/4 indicates 2. 20 indicates UN is an abbreviation for Shape…

A: Since you have asked multiple sub-parts only the first 3 subparts are solved for you, If you want…

Q: Consider following thread call-out 3/4-10 UNC-2B, what does the 2B mean? is the standard quality for…

A: 3/4 -10UNC -2B It shows that ¾  diameter unified coarse pitch of 2B class of fit screw thread.2B…

Q: I need answers to parts 4, 5, and 6, pertaining to the print provided.

A: 4.The minimum diameter of the bearing surface of the flange on the head is shown in the figure:

Q: A material has an mean indentation diameter of 3.64 mm created by a 5 mm diameter Brinell Indenter.…

A: Given data Mean indentation diameter (d) = 3.64 mm Diameter of brinell indenter (D) = 5 mm Hardness…

Q: D C B A NOTES: HEAT TREAT TO 58-60 HRC .500 TYP 2.0000+.0002 PROPRIETARY AND CONFIDENTIAL THE…

A: Given,  123 Super Block a) Material as per drawing: A2 Tool Steel b) Surface finish required Centre…

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.