16. A 30-m steel tape is used with a 50N force instead of the standard tension of 25N. If the cross-sectional area of thetape is 1.8 mm2, what is the tension error per tape length given that the Modulus of elasticity of steel 200Gpa17. A 30-m tape is supported only at its ends and under a steady pull of 8 kg. If the tape weighs 0.8 kg, determine tiesag correction (2pts) and the correct distance between the ends of the tape

Answered: Image /qna-images/answer/702bdae0-b49f-474c-a36c-3dfa22f546d2.jpg

16. A 30-m steel tape is used with a 5ON force instead of the standard tension of 25N. If the cross-sectional area of the tape is 1.8 mm2, what is the tension error per tape length given that the Modulus of elasticity of steel 200Gpa

16. A 30-m steel tape is used with a 5ON force instead of the standard tension of 25N. If the cross-sectional area of the tape is 1.8 mm2, what is the tension error per tape length given that the Modulus of elasticity of steel 200Gpa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

P = 8kN. Using N = 3, determine the allowable stress for A501 grade steel. Calculate the dimensions (to 1 decimal place) of a square rod. L = 5.9m. Calculate the deformation (6) and the strain (€).
If the temperature increases by 95°F, calculate the increase in stress for the steel segment shown. Assume the supports are unyielding and the bar is braced against buckling. E (psi) 10x10 Area (in?) a (in/in°F) 12.8x10-4 Steel Aluminum 2 1.5 29 x10 6.5x10- Steel Aluminum 10 in 15 in
Minimum of 3 decimal places in all computations.
Kindly write legibly. Thank you
A steel loop ABCD is placed around a 1.0 in. diameter aluminum rod AC. Cables BE and DF, each of 0.5 in. diameter, are used to apply the load Q. What is the largest allowable Q if the axial stress in cable BE stays under 23 ksi while the max axial stress in the aluminum rod AC is under 13 ksi? Reference: Beer, et.al., 7th Edition Mechanics of Materials 9 in. Į 9 in. ↓ A 12 in. 1 in. 4 E * F B D Q' 12 in. in. in. C
For the simply supported beam shown, a composite T-shaped section is to be used, shown below. Take the value of c, the distance between the top of the beam and the location of the neutral axis to be 56 mm. The beam is subjected to two point loads, each with of a value of 7.3 kN. At that point of maximum bending moment, determine the maximum direct tensile stress for the beam, given 1 = 6x 105 m². Give your answer in the form of MN/m² to 1 decimal place. Assume a tensile stress to be positive and a compressive stress negative. 3m 3m 3m INA N.A. T 350mm
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.
PROBLEM 4: The figure shows a plate that is fastened to a fixed to a fixed member by five 12-mm- diameter rivets. Compute the value of the loads P so that the shearing stress in any rivet does not exceed 79 MPa. 122 mm 40 mm 40 mm 102 mm -122 mm Figure 4
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
jp
Consider the figure below, depicting a simple beam AB supporting two equal concentrated loads P. *Inserted Photo* (Use the deformation sign convention. When entering expressions, use the following as necessary: P, L, and a.)