15. Knowing that the forces P and Q are equivalent to a single force R that passes through point A, determineP. (Hint: The combined moment of P and Q about A is zero.)Q150 N255 mmP/ 35° ---240 mm-+130 mm-l 14. Given that T = 28.3 kN and W = 25 kN, determine the magnitude and sense of the moments about point Bof the following: (a) the force T; (b) the force W, and (c) forces T and W combined.36 m16 m20 in

The combined moment of P and Q about point A is zero. Consider the moment equilibrium about point A.…

15. Knowing that the forces Pand Q are equivalent to a single force R that passes through point A, detemine P. (Hint: The combined moment of P and Q about A is zero.) Q- 150 N 255 mm +-130 mm P 35. 240 mm

15. Knowing that the forces Pand Q are equivalent to a single force R that passes through point A, detemine P. (Hint: The combined moment of P and Q about A is zero.) Q- 150 N 255 mm +-130 mm P 35. 240 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An experimental device imparts a force of magnitude F = 36 Ib to the front edge of the rim at A to simulate the effect of a slam dunk. Compute the moment of the force F about point O and about point B. The moments are positive if counterclockwise, negative if clockwise. Finally, locate a point C from the base at O to the location on the ground where the force imparts zero moment. The distance d from point O to point Cis positive if C is to the right of O, and negative if to the left. E 36" 28" F 17 12" 10' Answers: Mo -34,655 Ib-ft MB = -94.28 Ib-ft d = 7.33 ft
The 58 kg uniform beam (slender rod) is lying on the floor when the man exerts a force of F = 336 N on the rope, which passes over a small smooth peg at C. a) Determine the initial angular acceleration of the beam, in rad/s2. b) Find the horizontal reaction on the beam at A (considered to be a pin) at this instant. Express your answer in Newtons.
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x106 mm What is the value of the maximum moment in kN.m?
2a please help me with the answer and full solution
Please draw the complete free body diagram including the components. And give explanations for the correct Answer
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
2. Determine the moment over the support B of the beam shown in the figure. Using three-moment equation 1450 N/m m ஆனர் J 781 B 4m A 950 N 850 N Nm 1m 1m 2m
PART II. (BEAMS AND FRAMES : SHEAR AND BENDING MOMENT) DIRECTION : Answer the following questions. Provide complete and clear solution with illustration. PROBLEM N0. 1 Determine the reaction at supports B and D. Determine the maximum positive shear and maximum positive moment of the beam below using graphical method (Shear and Moment Diagram) 5 ΚN/M 4 KΝ/M 6 KN/M A B E .0 m- -4.0 m 4.0 m· -2.0 m D
Need right complete solution
Given a 2-D force system with geometry as shown. Find the magnitude of the equivalent couple moment (Nm) acting at O if P = 507 N , Q = 382 N, and T = 451 N . Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction of moment: use CW if clockwise , CCW if counterclockwise.
Situation 2 - The beam is acted upon by a uniform load as shown. The product EI = 1,000,000 where the modulus of elasticity is in Pascals, and the moment of inertia of the cross section is in m^4. 100 N/m A. 220.5 B. 212.4 TTT 5. Which of the following most nearly gives the vertical reaction at the roller in Newtons? A. 46.9 B. 51.9 A. B. 3 m 0.000213 0.000124 C. D. 6. Which of the following most nearly gives the moment reaction at the fixed end, in Newton-meters? 223.0 216.3 7. Which of the following most nearly gives the slope at the roller support in radians? 2 m 45.9 48.9 C. D. C. 0.000186 D. 0.000275
An experimental device imparts a force of magnitude F = 56 lb to the front edge of the rim at A to simulate the effect of a slam dunk. Compute the moment of the force F about point O and about point B. The moments are positive if counterclockwise, negative if clockwise. Finally, locate a point C from the base at O to the location on the ground where the force imparts zero moment. The distance d from point O to point C is positive if C is to the right of O, and negative if to the left.