Situation 2 - The beam is acted upon by a uniform load as shown. The product EI = 1,000,000 where the modulus of elasticity is in Pascals, and the moment of inertia of the cross section is in m^4. 100 N/m 3m 5. Which of the following most nearly gives the vertical reaction at the roller in Newtons? A. 46.9 B. 51.9 A. B. C. D. 0.000213 0.000124 6. Which of the following most nearly gives the moment reaction at the fixed end, in Newton-meters? A. 220.5 B. 212.4 2 m 45.9 48.9 C. D. 7. Which of the following most nearly gives the slope at the roller support in radians? 223.0 216.3 C. D. 0.000186 0.000275

Situation 2 - The beam is acted upon by a uniform load as shown. The product EI = 1,000,000 where the modulus of elasticity is in Pascals, and the moment of inertia of the cross section is in m^4. 100 N/m 3m 5. Which of the following most nearly gives the vertical reaction at the roller in Newtons? A. 46.9 B. 51.9 A. B. C. D. 0.000213 0.000124 6. Which of the following most nearly gives the moment reaction at the fixed end, in Newton-meters? A. 220.5 B. 212.4 2 m 45.9 48.9 C. D. 7. Which of the following most nearly gives the slope at the roller support in radians? 223.0 216.3 C. D. 0.000186 0.000275

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A у C n - Х 60° 40° B F = 800 lb

Q: 1. The wheel loads on a jeep are given. Determine the distance x so that the reaction of the beam at…

A: The given beam is simply supported beam so we can analyse this problem by using equilibirium…

Q: 18 В 58 7400 N с 18 0.80 m

Q: Situation B. An object is supported by two wires as shown below. The stress in either wire is not to…

A: Given:- Maximum stress in the wire = 30 ksi Free body diagram:-

Q: A у C n 60° х 40⁰ и B F = 800 lb

A: A force of 800 lb acting at 40° with rod which is inclined at angle 60° to the horizontal.

Q: Question # 3: The built-up beam is formed by welding together the thin plates of thickness 3 mm. the…

A: Shear center is a point on the beam section where the application of loads does not cause its…

Q: The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INa = 30x106…

Q: 2. The block of weight W2 is being held in its position by two cylindrical rollers resting on…

A: Given Coefficient of static friction for all contact surfaces is 0.36 W1 = 516 kN

Q: YA 20 mm 20° 100 mm 80 mm M

Q: A flat bar ABCDEF of negligible mass is hinged at A and supported by a roller support at D as shown…

A: Given data in question Point loads vertical as well as inclined Span member length Overhanging beam…

Q: Solution accu

Q: Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three…

A: Coplanar forces: In the coplanar force system, all the forces acting in one plane of action. They…

Q: Fhe truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Solution

Q: 1. A beam is loaded and supported as shown. Determine the components of the reactions at supports A…

A: The hinged support will have horizontal and vertical reactions. The roller support B will have…

Q: In a flywheel, an 800N-m is applied as shown below with a coefficient of belt friction 0.20. Minimum…

Q: released from rest in the mine how far the collar trave mentarily comes to rest. Ta

Q: Problem #1 Note num XN Use `105° 60° YN 1. If the 3 forces are in equilibrium, what is the…

Q: 12. Two designs for a beam are being considered, as shown in figure below. Which on will support a…

Q: H The internal shear force V at a certain section of a beam is 60 kN.m. If the beam has a…

A: Draw the figure.

Q: 4. A planar truss that is supported by a rolling pin support at point I and a fixed pin support at…

Q: (a) If w is constant, find an expression for the displacement of the beam. (b) The beam is fixed…

A: w = Kd4Hdx4 where K = EIK = Flexural RigidityE = Young's modulus I = Moment of inertia

Q: 2. Refer to Figure Q2, which shows a diagram of a loaded frame. Using the Principle of Virtual Work,…

Q: 5.) Consider the 2D beam supported by a roller at A and a pin at B. INTERNAL FORCES f) Is the…

Q: Question 17 A steel rod (E = 200 GPa) is fixed at A and subjected to the loading shown in the…

Q: Resolve the 300-lb force into components along (a) the x- and y axes and (b) the x'- and y-axes 200…

A: Hi there! by mistake, you have provided different force in the figure and the question body so, I am…

Q: e 390-kg drum has a center of mass at point G. The grip at B on member DAB sists both horizontal and…

A: Given:- mass=300kgTo find:-Ax,Ay,Nc,Nd

Q: PROBLEM 4: 1. SOLVE FOR THE MOMENTS PRODUCED BY EACH POINT FORCE and MOMENT. HINT: YOU HAVE TO…

A: Resolve each force into horizontal and vertical components.

Q: Derive the singularity equation of moment for the beam shown in figure I then:- 1- Draw bending…

A: RA=RB=12×2×8+8×2 =24 kNx=23m Bending Moment at distance 'x'…

Q: B 1500 N 15 m D 600 N/m

A: From the given information we have to consider the segment AG for analysis. The Segment BC has two…

Q: 6. For the beam shown, determine the following: A. moment of inertia of the section B. absolute…

Q: With reference to the figure below, the total force (F) of the liquid on the plane surface and the…

Q: The triangle section AB beam, bearing the load F1 = 400 daN in the figure, is produced from a…

A: FOS=3 width of triangular beam b=8 cm FOS=ultimate shear stressworking shear stress 3=1800working…

Q: Determine the resultant. Find also the value of F and 8.

Question

Situation 2 - The beam is acted upon by a uniform load as shown. The product EI = 1,000,000
where the modulus of elasticity is in Pascals, and the moment of inertia of the cross section is in
m^4.
100 N/m
A. 220.5
B. 212.4
TTT
5. Which of the following most nearly gives the vertical reaction at the roller in Newtons?
A. 46.9
B. 51.9
A.
B.
3 m
0.000213
0.000124
C.
D.
6. Which of the following most nearly gives the moment reaction at the fixed end, in
Newton-meters?
223.0
216.3
7. Which of the following most nearly gives the slope at the roller support in radians?
2 m
45.9
48.9
C.
D.
C. 0.000186
D. 0.000275

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Slope and displacement expression

VIEW

Step 3: Boundary conditions

VIEW

Step 4: Moment reaction and slope calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the bending stress about the y-axis at points A and B. Indicate if the stress is in tension or compression. 200kN m B 200mm ▶44 15mm 200mm A 400mm 20mm
Help please!
Mechanics of Deformable Bodies Kindly answer it as soon as possible, our topics is stresses in beams. please answer it with comple solution and diagram. Thankyou
The circular shaft AB consists of a 18 mm diameter solid steel cylinder in which a 8 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 50 Nm. Determine the ratio of lengths L₁/L₂. Input your answer to two decimal places. 4₁ L₂ A 150 Nm B
The bending moment capacity of the trapezoidal section given in the figure, the equivalent rectangular stressCalculate with equilibrium equations by accepting the block. C25/S420 d’ = 40 mm
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
A simply supported steel beam is loaded with a uniformly distributed load and a torque. The beam has a U-shaped cross section, as shown. Determine the maximum normal compressive and tensile stresses caused by the acting loads. Express your answer in kgf/cm2 and in MPa.
Question 5 T/2 В 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member BC. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm
1.) 600 lb Determine: 900 lb - The resultant force (R) - The angle 0 between the R and the x-axis 40 35°
Please solve it fast. Within 20-30min
A fixed beam is loaded with the following distributed load: qix) = 8* sin( Tx ) [N/m) XE (0,2) (m) Vhat is the magnitude of the equivalent force acting on the beam? What is the magnitude of the equivalent moment acting on the beam relative to the fixed end at x=0? [Nm]