Answered: 1. Determine the Moment due to force F…

1. Determine the Moment due to force F about: a. Point O b. Point B Note: The thickness of the beam is NOT negligible and is given in the image. Y ///// F=225N 9m 3m 25 t sm B 2m O

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SP=80 N 40° F=200 N 200 mm W=140 N V3 C= 20 Nm FIGURE C 100 mm H-90 N 米 200 mm 400 mm 6. An angular bracket shown is acted upon by forces and couple applied in the direction and location indicated. Compute the moment acting at point O. Refer to Figure c. a. 71, 705 N-mm 2 b. 40, 294 N-mm G c. 77,064 N-mm G d. 74,935 N-mm
PART II. (BEAMS AND FRAMES : SHEAR AND BENDING MOMENT) DIRECTION : Answer the following questions. Provide complete and clear solution with illustration. PROBLEM N0. 1 Determine the reaction at supports B and D. Determine the maximum positive shear and maximum positive moment of the beam below using graphical method (Shear and Moment Diagram) 5 ΚN/M 4 KΝ/M 6 KN/M A B E .0 m- -4.0 m 4.0 m· -2.0 m D
The value force of P The value force of F
Express force F in Cartesian vector form if point B is located 3 m along the rod from end C.
Assume that Wo = 42 N/m, L = 2 m, and El constant for the beam. Find the deflection of the beam at the free end. Wo B O -52.2/EI O-44.6/EI O -39.6/EI O -67.4/EI O -61.6/EI
e E:10 * ZAIN IQ Iı. 团 / G3.png Determine the magnitude of the component force F2 in Fig. and the magnitude of the resultant force FR if FR is directed along the positive Y axis. 45 F2 F1 Y Q2/ Determine the resultant moment of the force about point C F =400N 100 N D. 30° A 45° 0.3 m B 100 N 0.4m tozm t
PROBLEM : Determine the angle e for equilibrium of the lever shown . Distegard the weights of bars AB and BC , Bak 2 M. 900 200 N 100 N 1m.
Please solve in 30 minute
7. Determine the flange width b if it is required that the centroidal moments of inertia I, and I, be in the ratio 3 to 1, respectively. 15 mm 250 mm C 15 mm 15 mm
P1=306N and P2=139N. Determine the moment at x,y and z axis in N.m. Write numerical value only in 2 decimal places.
Link AB rotates through a limited range of the angle ẞ, and its end A causes the slotted link AC to rotate also. For the instant represented where B 60° and ẞ=0.6 rad/s constant, determine the cor- responding values of ŕ, F, 8, and . Make use of Eqs. 2/13 and 2/14. Ans. 77.9 mm/s, 7=-13.5 mm/s² =-0.3 rad/s, -0 C A 150 mm B B 150 mm
A III [ 2 m d 300N B 3m 307 M=1500Nm For the above diagram, given that F₁-800 N, w = 400 N/m and d = 4 m, calculate the following (neglect the depth of the beam). Note that there is a pin support at A and a roller support at B. 1. The magnitude of the resultant of the applied forces, FR. Please provide the answer in kilo Newtons and report the answer to three significant figures. Please include the unit ("kN") within your answer. 2. The angle of the resultant forces, FR measured counter-clockwise from the negative x axis. Please provide the answer in degrees and report the answer to three significant figures. 3. Locate the resultant forces, FR so that it is equivalent to the system of applied forces. Calculate the offset distance of the resultant force, FR measured from point A. Please provide the answer in metres and report the answer to three significant figures.