The horizontal force F acts on the handle of the wrench (i.e Fis parallel to xy-plane). What is x-component of themoment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 30°.ofB

When forces acting on any body then by applying the equilibrium condition in static will give us the…

Answered: The horizontal force F acts on the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment of the force of F = 600 N about point A.
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
The cord passing over the two small pegs A and B of the board is subjected to a tension of T = 100 N. The resultant couple moment produced by the two cords is 20 Nm, clockwise. Part A Determine the minimum tension P of the cord passing over pegs C and D. P = 16.35 N T 30° Part B Determine the corresponding orientation angle of the cord passing over pegs C and D. 0 45 A 300 mm D B 30⁰ -T 300 mm
A cross section of truck frame is shown. Determine the location of the shear center O due to 1-kip vertical shearing force applied at O
I know BE is a zero force member but I can't find the force applied at BD? Also state if it's in compression or tension.
ferce F = {400i – 100j – 700k} lb acts at the end of the beam. Determine Problem 2: The %3D - the moment of this force about point O. F В 8 ft 1.5 ft 0.25 ft
STATICS OF RIGID BODIES (CHOOSE THE CORRECT ANSWER IN THE CHOICES. WRITE THE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED.)
5- Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the wrench and the point P(x, y) where its line of action intersects the plate. F, = |-300k) N %3D Fe= [200j| N 2m 500N 30 F = (4001) N
Ye 2. Two channels are welded to two 12 in. x 1 in. plates. For each channel, the following are known: w = 4 in. Icx = 61 in* Determine the moments of inertia, I, and Iy, about the centroid axes. h = 10 in. Ac = 7 in? b = 1 in. Icy = 2.5 in Ans: I = 850 in“, I, = 419 in* h y Xc 1 in. 5 in. W 5 in. 1 in. 6 in. 6 in.
Determine the equivalent force-couple system at the center O for each of the three cases of forces (F = 110 N) being applied along the edges of a square plate of side d = 540 mm. The couple is positive if counterclockwise, negative if clockwise.
Ans - Normal force is -41.25 kN. Also find moment at C.
Draw the Moment of all members.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The horizontal force F acts on the handle of the wrench (i.e F is parallel to xy-plane). What is x-component of the moment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 = 30°. B