The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm

Q: The system under the effect of torsion; a- Draw the torsional moment diagram. b- Determine the…

A: Determine a. Draw the torsional moment diagram. b. Angle of rotation at point C. c. Shear stress.

Q: A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a…

A:

Q: E 240 mm F A 20 mm 180 mm D

A: Data Given: Asked: Reactions of collar A and Tension in the wire

Q: Two forces P and Q are applied as shown to an aircraft connection. TA 60° 30° B Knowing that the…

A:

Q: An 800 N-m couple is applied to the flywheel as shown. The coefficient of belt friction is 0.20. The…

A:

Q: Q9. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. %3D (a) If the…

A: Solution; Given that: L=0.90 m r1=40mm

Q: The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of…

A:

Q: The figure above is a skycam which is supported by 2 wires (assume that no wires holding at the top…

A: This question related to the Strength of material. In this question we calculate the tensile…

Q: 1. Determine the maximum torque Tin kN-m without exceeding a shear stress of 70 MPa in steel and 50…

A: Given, Gst = 83 GPa or 83000 MPa Gbr = 35 GPa or 35000 MPa

Q: Problem 4 In the structure shown below, each of the rods BD and CE is made of brass (E = 105 GPa)…

A: moment at F will be zero.

Q: *13-24. An L-2 tool steel link in a forging machine is pin connected to the forks at its ends as…

A: Given values: Case 1: Ends are pinned. L=24 in. Case 2: Ends are fixed. L=24 in.   FOS = 1.75

Q: 530 N 310 285 310 mm mm mm 325 mm 550 mm 325 mm

A: Consider the given figure. The vertical reaction at point B is By. The horizontal reaction at point…

Q: eed the answer to the question in engineering resistance

A: GIVEN E=38 GPA lA=5 mm lB=3mm

Q: a. Determine the reaction at the least critical bolt.  b. Determine the total torque being resisted…

A: P = 400KN

Q: The copper pipe (G - 45GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fxed…

A: We have to determine the value of rotation of the free end with respect to the fixed end of the…

Q: he to The structure loaded as shuwn : he 4m P 40 KN E 200 GPa 12=1c_100 x 10° mm • Solve the…

A:

Q: HW (4-1): If the area of each bar of the truss shown in 2w figure is (2700 mm') and the movement of…

A: Calculate the moment about A as; ∑MA=01×10-RD×cos4.5°×10+RD×sin45°×30=0RD=-0.707 kN Calculate the…

Q: The aluminum rod AB GPa) iš bondéd tỏ tó the brass rod BD (G = 39 GPa). Knowing that portion CD of…

A:

Q: 200 kN В D C - 3 m →- 3 m - 3 m 3 m Circular cross-section ABCDE beam has variable moment of…

A: Solution; Given that; (a) Number of links, n=2 number of joint, J=1 Number of higher pair (point…

Q: The wooden strut is subjected to the loading shown. Draw the state of stress at point C on an…

A:

Q: Q12 (Simple stress and strain) Item 3 of 3 A bar AB (A = 500 mm?) is hinged at A and is supported by…

A: Given Data:A=500mm2W=90kND=20mmE=200Gpa

Q: The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fixed…

A: Given:- The modulus of rigidity  of the steel pipe = G = 75 GPa The outer diameter of the pipe = 50…

Q: . In the figure below, the boom AC is supported in a ball and socket joint at C and by the cables AD…

A:

Q: 8) If the elongation of wire BC is 0.2 mm after the force P is applied, determine the magnitude of…

A: Given :

Q: L 0.75d A T а-

A:

Q: Problem 7: The bar AB is supported by two smooth collars. At A the connection is with a ball-…

A: ∑ Fx=0Ax+Bx=0......(1)∑ Fz=0Az+Bz=0......(2)

Q: by assemb engineers can rotate in a vertical plane combined effect of gravity and a couple M od BC.…

A: Given:- mass=2.25kg of slender rodAB 1.85kg slender rod BC pin at B chord AC tension in chord…

Q: Calculate the maximum intensity w of the uniform distributed load that can be applied on the beam…

A:

Q: O O OO O o o W shape

A:

Q: Determine the reaction at the support at bar (3).

A:

Q: 1. Hibbeler 9-2 For the beam shown El is constant a) Use flexibility (method of consistent…

A: Objective: solve the beam using flexibility method. Solution: In this case we need to find the basic…

Q: The cam is subjected to a couple moment of X. Determine the minimum force P that should be

A: f=0.45N2∑ Mo=08.8-0.3×N20.06-N20.01=0N2=314.2857N

Q: Calculate the support reactions of the column element given in the figure. Determine the required…

A:

Q: The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: The wires are unstretched in the horizontal positionclockwise rotationTo find:average normal strain…

Q: The 0.5-kg flyballs of a centrifugal governor revolve at a constant speed v in the horizontal circle…

A: M=0.5 Kg=1.2 lb R=150 mm = 6 inch F=75 N=17 lb

Q: The 6m long steel shaft has a torque of 12 kN-m applied at the free end. The angle of twist of the…

A: We have to determine the value of diameter of the shaft as per the given data like 6 m long shaft…

Q: The rope ABexerts a 46 - N force T on the collar at A Let rCa be the position vector from point C to…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.