14000 1.435 12000 1.430 10000 1.425 8000 1.420 6000 1.415 4000 1.410 2000 1.405 1.400 45 15 20 25 30 35 40 Temperature ["C] +dynamic viscosity ImPas) density [g/cm") Figure 1 (a) As shown in Figure 1, viscosity and density of honey was found to decrease with increase in temperature. Explain the reasons behnd these phenomenon related to Fluid Mechanics in microscopic view. Dynamic viscolsty [mPa.s] Density [g/cm]

14000 1.435 12000 1.430 10000 1.425 8000 1.420 6000 1.415 4000 1.410 2000 1.405 1.400 45 15 20 25 30 35 40 Temperature ["C] +dynamic viscosity ImPas) density [g/cm") Figure 1 (a) As shown in Figure 1, viscosity and density of honey was found to decrease with increase in temperature. Explain the reasons behnd these phenomenon related to Fluid Mechanics in microscopic view. Dynamic viscolsty [mPa.s] Density [g/cm]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hemispherical container, 26 inches in diameter, is filled with a liquid at 20°C and weighed. The liquid weight is found to be 1617 ounces. What is the density of the fluid in kg/m3? ]kg/m3
To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
Lab 2-Measurement Asynch - Tagged.pdf Page 4 of 7 ? Part I: Taking Measurements & Estimating Uncertainties for a single measurement www.stefanelli.eng.br The mass of the object is_ 0 i Parts on a tripie peam palance 0 0 10 20 30 1 100 2 3 40 200 4 +/- 50 60 70 5 300 7 400 80 Qv Search 8 90 9 500 100 9 10 g www.stefanelli.eng.br
An airplane wing model is designed with a similarity test. The lift force is a function of speed, chord, density, viscosity, speed of sound, and angle of attack. FL = f (V, Lc, p, μ, c, a) Determine the dimensionless numbers that represent the problem (develop in evidence)
Fill in blank hell
1.3 A mixture of two liquids of equal volume is made, the one has a relative density of 0,8 and the other a density of 980 kg/m³. What will the weight of 2 500 litres be? 1.4 1.5 1.6 15 1.7 [21830 N] A solid block of stone with a relative density 4 is broken down and crushed to an average size of 20 mm. If the stone originally had a volume of 50 m³, how many truck loads with a volume of 2 m³, will it take to transport the crushed stone if 25 of the crushed stone has a mass of 80 kg. Has the relative density changed? How much? Why? [32 truck loads] Use table 1.4.2 to determine the kinematic viscosity of crude oil with a density of 855 kg/ m³ at temperatures of 20°C and 100°C. [9,357 x 10-6 m²/s; 3,275 x 10-6 m²/s] Air is used in a sensitive gyroscope to keep the metal bearing surfaces apart. Will the friction losses in the bearing be higher, lower or the same if the temperature of the bearing increases? A widely used S.I. unit for kinematic viscosity is centi- stoke cSt. One stoke is…
1. To determine the dynamic viscosity of a liquid you take repeated measurements of the liquid density and kinematic viscosity. These data are summarized in the following table: Avg. measurement Total Uncertainty P 999 kg/m³ ±0.5% V 1.23 mm²/s ±0.01 mm²/s kg Ns What is the dynamic viscosity? Give dynamic viscosity in units of; which is the same as ms 2. Determine the absolute and relative uncertainties in the dynamic viscosity.
Surface tension is due to uneven molecular attraction between immiscible fluid media and solid surface. Its importance is governed by dimensionless parameter Which of the Inertia force called Weber number given by We = Surface tension force™ following statements are correct? (i) Surface tension becomes important when the length scale L is small such as in ink jet printing, coating of thin film, oxygenation of water by falling rain drops. (ii) 111 Super-hydrophobicity can be achieved by micro/nano texturing of surface such as in lotus leave, butterfly and dragonfly wing. During oil spill in ocean, oil floats and spreads out due to gravity. By conservation of mass, the oil film becomes thinner as it spreads. Finally, the surface tension force becomes important causing the formation of tiny oil droplets. (A) (B) (C) (D) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above
Pressure drop AP depends on four variables: the diameter of the pipe D, the density of the fluid p, the kinematic viscosity of the fluid v and the mean velocity v. Applying Buckinham's Pi Theorem, a dimensionless pi-group can be identified using the following power product: [AP] = [D]ª[p]b[v][v]ª. Which of the following statements in term of [T] is correct? Select one: O [T]: -2 = -c-d [T]: -1 = -c-d [T]: -2 = -c-2*d [T]: -2 = -2*c-d [T]: -2=-c+d
Can you help with both please.
Vibration
An elastic foundation is often used to support heavy machinery that vibrates in such a way to cause problems for the rest of the structure. An elastic foundation with two equal springs each of stiffness k = 600 lbs/in is used to support the equipment of weight W = 1000 lbs shown. The equipment vibrates in such a way that it causes a vertical forcing function P(t) = 100 sin(20t) [lbs]. %3D (a) Draw the degree of freedom for the motion of the machinery. (b) Determine the equation of motion. What type of motion is this? (c) Determine the natural frequency and the displacement of the machinery. (d) What is the maximum amount of force that will be felt by the rest of the structure? (Think about what causes force to the rest of the structure) Rest of structure Hww