120 V 0.5 A 104 V 0.3 A 7 76 V 0.3 A 28 V 0.3 A 3 4 60 V 60 V 0.5 A 0.5 A 6. RATING 5

Q: 3. Determine the total resistance and the total current. 100V 1 + 1002 M 15.2. M 1502 500 1052 1022

A:

Q: From the following figure, find voltage at the dependent source 601, 250 2 24 V 50 Ω 150 Ω O a. 24 V…

A: For this problem we can easily found dependant voltage value by using nodal analysis.

Q: 5. Determine the total resistance if each R is 8Ω. RT M. N M W W W N

A: In this question we need to find a equivalent resistance of the given circuit.

Q: j) Explain the regulator characteristics. k) Explain how the regulator characteristics should be in…

A:

Q: (a) (b) (c) (d) Sketch the spectra of m(t) = cos(2л50t) + 2 cos(27150t) and m(t) = sin (2n50t) sin…

A:

Q: Determine Rin(tot) of the circuit: 20 V 22 k B=140 12 ka= 10 uF

A:

Q: 3.5V 43V 27V ww ww wW. 1SV 小24V 6.2V V5 Figure 14 A 5.8 V 4.7 V C 16.7 V 17.8 V O A

A:

Q: 3. Determine Req if each R is 5 ohms. M M W -M N M

A: We need to determine the equivalent Resistance, Req.

Q: The equivalent resistance between points a and b in the figure is 5.000 ww 10.00 5,000 W 4.00 W…

A:

Q: (4) 0,lkn 3v 5V DA Vo Paw Vo

A: We need to find out output voltage and we need to draw it .

Q: The equivalent resistance between L and M of the circuit 6.2 L 14.02 205 20 10.02

A: Given circuit,

Q: Identify the nodes in the following circuit. How many nodes are there in total? 470 uF 470 uF 1000…

A: Node is a junction/point in the circuit where two or more than two branches are connected. if 2…

Q: A mixed circuit is shown in the figure below. For each resistor, its voltage and current, as well as…

A: Given circuit,Asked to find the current and voltage in each resistor.And Total resistance seen by…

Q: 6 Q/ how much The number of parallel resistances ? R1 M 2 R3 5 R2 M R5 3 R4

A:

Q: SV 15 ( 25 f wwwww 50 SV Determine the current 1 in this circuit

A: Given data, Circuit diagram is given as,

Q: Figure 5 shows a current series feedback amplifier. The sampled current signal is the output…

A:

Q: C3 R1 1.0 kO 0.022 uF C2 R4 +. 0.047 µF 0.047µF 1.0 k 1.0 k? R3 560 2 R2 R- 560 2 1.0 k2 0.022 uF Rs…

A:

Q: What's wrong with this connection?

A: The circuit you have tried is the Series RC circuit. The breadboard contains two regions and they…

Q: 2. (a) For the circuit in Fig. 2, obtain the Thevenin equivalent at terminals a-b. (b) Calculate the…

A:

Q: What is the approximate value of the total resistance. R2 RS R11 4 kOhm 4 kOhm 5 kOhm R128 kOhm R310…

A: In this question,  We need to calculate the equivalent resistance.  We know if two resistances R1…

Q: U8 A'S )Determine the current supplied by each Battery in the Grcuit

A: Given:-

Q: 7. Determine all of the resistor values in figure below. if RT = 7730. 15.53 mA R₁ 3.64 mA R₂ ww +1₁…

A: Given Circuit:Total resistance, To determine:Value of resistances

Q: R 20 V D 3A 10.02 www 25 (1 w 360

A:

Q: From the circuit below, determine the current IR flowing through the resistor RL. Rs= 50 2 Vz = 8.2…

A: The solution is given below

Q: what is the puwer burned into Re q maaimizes Pz what value of R

A:

Q: Determine the total resistance, R W RT 6&R 41.5 8ksz

A:

Q: +20 V Rc RE -20 V Vc An NPN transistor in active mode has the following characteristics: B = 150 Use…

A:

Q: iv. Use Nodal Analysis to find the voltage V 5.89 V v. The current in R4 is: 24 mA

A:

Q: 13 R3 R1 R2 R4 V2

A: We check twice We are getting VX= 5.049 Volt And Ix= -2.27 A

Q: Determine the current 13, in Amperes, if E R1 R2 R3 R4 R5 24 V 0.3 0 24 Q 0.3 0 15 Q 16 0 I3 'R, R2…

A:

Q: Determine the V, voltage in the circuit of 42 100/45 V 10 2 Ve

A:

Q: Determine the voltage Vcrand the current Ifor the following circuit. B=60 RE 1.2 k2 RC 2.4 kl 4 V Ve…

A: Determine the voltage VCB  and the current IB  for the following circuit?

Q: What is the total resistance. R2 R5 4kOhm 1kOhm R1 3kOhm R3 1kOhm R4 2kOhm R6 2kOhm

A:

Q: Compute for re of the given circuit. 22 V 5.6 k2 1. 330 k2 Cc B = 80 T=40 k2 Cc 1.22 0.47 k2 CE O…

A: The solution is given below

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.